TELEDYNE API T300 Operation Manual Download | Manualshive

Page: 170 / 347

background image

Data Acquisition System (DAS) and APICOM

Teledyne API – Model T300/T300M CO Analyzer

168

7.1.7.

SAMPLE PERIOD AND REPORT PERIOD

The DAS defines two principal time periods by which sample readings are taken and
permanently recorded: Sample and Report periods.

•

SAMPLE PERIOD:

Determines how often DAS temporarily records a sample

reading of the parameter in volatile memory.

SAMPLE PERIOD

is only used when

the DAS parameter’s sample mode is set for

AVG

,

SDEV

,

MIN

or

MAX.

The

SAMPLE PERIOD

is set to one minute by default and generally cannot be

accessed from the standard DAS front panel menu, but is available via the
instrument’s communication ports by using APICOM or the analyzer’s standard
serial data protocol.

•

REPORT PERIOD:

Sets how often the sample readings stored in volatile memory

are processed, (e.g. average, minimum or maximum are calculated) and the results
stored permanently in the instrument’s Disk-on-Module as well as transmitted via the
analyzer’s communication ports. The Report Period may be set from the front
panel. If the INST sample mode is selected the instrument stores and reports an
instantaneous reading of the selected parameter at the end of the chosen report
period.

06864D DCN7562

«
...
168
169
170
171
172
...
»

Summary of Contents for T300




























































































































































































































































































































































Reviews:

No comments

Related manuals for T300

Brand: UEi Pages: 20

Brand: Hach Pages: 138

Brand: P3 International Pages: 2

Brand: Danfoss Pages: 80

Brand: Palstar Pages: 15

Brand: Palstar Pages: 37

Brand: LD Didactic Pages: 2

Brand: Aqua Lung Pages: 24

Precision KMS7101

Brand: Kreg Pages: 16

Brand: Kinesys Pages: 10

Brand: REED Pages: 20

Brand: Pilot Communications Pages: 34

Brand: ASD Pages: 72

Everywhereyoulook Frontline X500

Brand: Teledyne Lecroy Pages: 8

Brand: Haltech Pages: 20

Brand: R.M. Young Pages: 11

Brand: Oakton Pages: 80

Brand: i-SENS Pages: 133

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands