TELEDYNE API T300 Operation Manual Download | Manualshive

Page: 180 / 347

background image

Data Acquisition System (DAS) and APICOM

Teledyne API – Model T300/T300M CO Analyzer

178

7.2.2.

DAS CONFIGURATION USING TERMINAL EMULATION

PROGRAMS

Although Teledyne API recommends the use of APICOM, the DAS can also be
accessed and configured through a terminal emulation program such as HyperTerminal
(see example in Figure 7-4).

To do this:

•

All configuration commands must be created and edited off line (e.g. cut & pasted in
from a text file or word processor) following a strict syntax (see below for example).

•

The script is then uploaded via the instrument’s RS-232 port(s).

Figure 7-4:

DAS Configuration Through a Terminal Emulation Program

Both of the above steps are best started by:

1. Downloading the default DAS configuration.

2. Getting familiar with its command structure and syntax conventions.

3. Altering a copy of the original file offline.

4. Uploading the new configuration into the analyzer.

I

MPORTANT

I

MPACT ON

R

EADINGS OR

D

ATA

Whereas the editing, adding and deleting of DAS channels and
parameters of one channel through the front-panel control buttons can
be done without affecting the other channels, uploading a DAS
configuration script to the analyzer through its communication ports will
erase all data, parameters and channels by replacing them with the new
DAS configuration. Backup of data and the original DAS configuration is
advised before attempting any DAS changes.

06864D DCN7562

«
...
178
179
180
181
182
...
»

Summary of Contents for T300




























































































































































































































































































































































Reviews:

No comments

Related manuals for T300

Brand: Bacharach Pages: 19

Brand: E+E Elektronik Pages: 32

Brand: VELOCICALC Pages: 6

Brand: Panametrics Pages: 68

Brand: ICM Controls Pages: 8

Brand: T&D Pages: 2

Brand: T&D Pages: 2

Brand: Tavool Pages: 12

Brand: UEi Pages: 8

Brand: OHAUS Pages: 71

Brand: Parker Pages: 16

Brand: Waterproof Pages: 51

Brand: OmegaWatt Pages: 9

Engine Analyzer Series

Brand: ACCEL DFI Pages: 39

Panametrics XDP

Brand: Baker Hughes Pages: 64

Brand: IROX Pages: 8

Brand: Hanna Instruments Pages: 24

Brand: Hach Pages: 2

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands