TELEDYNE API T300 Operation Manual Download | Manualshive

Page: 234 / 347

background image

Maintenance Schedule & Procedures

Teledyne API – Model T300/T300M CO Analyzer

232

10.3.

MAINTENANCE PROCEDURES

The following procedures are to be performed periodically as part of the standard
maintenance of the T300.

10.3.1.

REPLACING THE SAMPLE PARTICULATE FILTER

The particulate filter should be inspected often for signs of plugging or contamination.
We recommend that the filter and the wetted surfaces of the filter housing are handled as
little as possible when you change the filter. Do not touch any part of the housing, filter
element, PTFE retaining ring, glass cover and the o-ring.

To change the filter:

1. Turn OFF the analyzer to prevent drawing debris into the instrument.

2. Open the T300 Analyzer’s hinged front panel and unscrew the knurled retaining ring

on the filter assembly.

Figure 10-1:

Sample Particulate Filter Assembly

3. Carefully remove the retaining ring, PTFE o-ring, glass filter cover and filter element.

4. Replace the filter, being careful that the element is fully seated and centered in the

bottom of the holder.

5. Re-install the PTFE o-ring (with the notches up), the glass cover, then screw on the

retaining ring and hand tighten. Inspect the seal between the edge of filter and the
o-ring to assure a proper seal.

6. Re-start the Analyzer.

06864D DCN7562

«
...
232
233
234
235
236
...
»

Summary of Contents for T300




























































































































































































































































































































































Reviews:

No comments

Related manuals for T300

Brand: QUBINO Pages: 2

Brand: Sanmenxia Pages: 17

Brand: SANKO Pages: 25

Brand: Samson Pages: 2

Brand: Sage Pages: 68

Brand: Lutron Electronics Pages: 20

Brand: Rion Pages: 4

Brand: Neogen Pages: 9

Brand: Raytech Pages: 7

Brand: TA Instruments Pages: 68

Brand: Isspro Pages: 2

LaserDIMENSIONMASTER 3336

Brand: Calculated Industries Pages: 2

Brand: PTC Instruments Pages: 2

KS-PH-221-DELUXE

Brand: Kensington Pages: 14

Brand: xDEEP Pages: 57

Brand: Simpson Pages: 19

Brand: Akai Pages: 12

Brand: CESVA Pages: 9

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands