TELEDYNE API T300 Operation Manual Download | Manualshive

Page: 236 / 347

background image

Maintenance Schedule & Procedures

Teledyne API – Model T300/T300M CO Analyzer

234

5. If the instrument has one of the zero and span valve options, the normally closed

ports on each valve should also be separately checked. Connect the leak checker
to the normally closed ports and check with soap bubble solution.

6. Once the leak has been located and repaired, the leak-down rate should be < 1 in-

Hg (0.4 psi) in 5 minutes after the pressure is shut off.

10.3.4.

PERFORMING A SAMPLE FLOW CHECK

CAUTION

G

ENERAL

S

AFETY

H

AZARD

Always use a separate calibrated flow meter capable of measuring flows in the 0 – 1000

cm

3

/min range to measure the gas flow rate though the analyzer.

DO NOT use the built in flow measurement viewable from the Front Panel of the

instrument. This measurement is only for detecting major flow interruptions such as

clogged or plugged gas lines.

See Figure 3-4 for SAMPLE port location.

1. Attach the Flow Meter to the sample inlet port on the rear panel. Ensure that the

inlet to the Flow Meter is at atmospheric pressure.

2. Sample flow should be 800 cm

3

/min

±

10%.

3. Once an accurate measurement has been recorded by the method described

above, adjust the analyzer’s internal flow sensors (See Section 9.6.3).

Low flows indicate blockage somewhere in the pneumatic pathway, typically a plugged
sintered filter or critical flow orifice in one of the analyzer’s flow control assemblies.
High flows indicate leaks downstream of the Flow Control Assembly.

10.3.5.

CLEANING THE OPTICAL BENCH

The T300/T300M sensor assembly and optical bench are complex and delicate.
Disassembly and cleaning is not recommended. Please check with the factory before
disassembling the optical bench.

10.3.6.

CLEANING EXTERIOR SURFACES OF THE T300/T300M

If necessary, the exterior surfaces of the T300/T300M can be cleaned with a clean damp
cloth. Do NOT submerge any part of the instrument and do NOT use any cleaning
solution.

06864D DCN7562

«
...
234
235
236
237
238
...
»

Summary of Contents for T300




























































































































































































































































































































































Reviews:

No comments

Related manuals for T300

Brand: Atomos Pages: 4

Brand: Xsens Pages: 4

Brand: Eastron Pages: 2

Brand: EASTERN INSTRUMENTS Pages: 3

Brand: Vaisala Pages: 2

Brand: X-Rite Pages: 45

Brand: X-Rite Pages: 22

Brand: ASCEL Electronic Pages: 64

Brand: Axio MET Pages: 5

PRO VPR100 Series

Brand: CTC Union Pages: 10

Brand: PCB Piezotronics Pages: 15

Brand: Sercel Pages: 63

Brand: M & I Instruments Pages: 3

Brand: SANKO Pages: 97

Brand: Staco Energy Pages: 2

Brand: Bahco Pages: 21

Brand: Kübler Pages: 72

Brand: OmegaWatt Pages: 9

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands