TELEDYNE API T300 Operation Manual Download | Manualshive

Page: 242 / 347

background image

Troubleshooting and Service

Teledyne API – Model T300/T300M CO Analyzer

240

Table 13-1: Warning Messages – Indicated Failures (cont.)

WARNING

MESSAGE

FAULT CONDITION

POSSIBLE CAUSES

SAMPLE TEMP

WARN

Sample temperature is < 10

o

C or >

100

o

C.

Ambient temperature outside of specified range
Failed bench heater
Failed bench temperature sensor
Relay controlling the bench heater
Failed relay board
I

2

C bus

SOURCE WARNING

Occurs when CO Ref is <1250

mVDC or >4950 mVDC.

Either of these conditions will result

in an invalid M/R ratio.

GFC Wheel stopped
Failed sync/demod board
If status LEDs on the sync/demod board ARE flashing the cause is
most likely a failed:
IR source
Relay board
I

2

C bus

IR photo-detector

SYSTEM RESET

The computer has rebooted.

This message occurs at power on.  If you have not cycled the power
on your instrument:
5 VDC power,
Fatal error caused software to restart
Loose connector/wiring

WHEEL TEMP

WARNING

The filter wheel temperature is

controlled at 68

±

2

°

C

Blocked cooling vents below GFC Assembly. Make sure that
adequate clear space beneath the analyzer.
Analyzer’s top cover removed
Wheel heater
Wheel temperature sensor
Relay controlling the wheel heater
Entire relay board
I

2

C bus

11.1.2.

FAULT DIAGNOSIS WITH TEST FUNCTIONS

Besides being useful as predictive diagnostic tools, the test functions viewable from the
front panel can be used to isolate and identify many operational problems when
combined with a thorough understanding of the analyzer’s Theory of Operation (see
Section 12).

The acceptable ranges for these test functions are listed in the “Nominal Range” column
of the analyzer

Final Test and Validation Data Sheet

(T300, P/N 04307 and T300M,

P/N 04311) shipped with the instrument. Values outside these acceptable ranges
indicate a failure of one or more of the analyzer’s subsystems. Functions whose values
are still within the acceptable range but have significantly changed from the
measurement recorded on the factory data sheet may also indicate a failure.

06864D DCN7562

«
...
240
241
242
243
244
...
»

Summary of Contents for T300




























































































































































































































































































































































Reviews:

No comments

Related manuals for T300

Brand: Vcheck Pages: 31

Brand: Eagletone Pages: 2

Brand: WattNode Pages: 57

Brand: Kanomax Pages: 31

Brand: Hach Pages: 196

Brand: Campbell Pages: 25

Brand: Larson Davis Pages: 2

Brand: G-Tek Pages: 27

Brand: Halcyon Pages: 36

Brand: Omega Pages: 74

Brand: Omega Pages: 24

Brand: SAGEMCOM Pages: 33

Prestige Series

Brand: Ibanez Pages: 54

Brand: E-Mon Pages: 72

Brand: IDEAL Pages: 84

Brand: Lutron Electronics Pages: 43

Brand: C.R. Laurence Pages: 4

Brand: Neogen Pages: 9

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands