TELEDYNE API T300 Operation Manual Download | Manualshive

Page: 251 / 347

background image

Teledyne API – Model T300/T300M CO Analyzer

Troubleshooting and Service

249

11.2.

GAS FLOW PROBLEMS

When troubleshooting flow problems, it is a good idea to first confirm that the actual
flow and not the analyzer’s flow sensor and software are in error, or the flow meter is in
error. Use an independent flow meter to perform a flow check as described in Section
10.3.4. If this test shows the flow to be correct, check the pressure sensors as described
in Section 11.5.7.6.

The T300/T300M has one main gas flow path. With the IZS or zero/span valve option
installed, there are several subsidiary paths but none of those are displayed on the front
panel or stored by the DAS.

With the O

2

sensor option installed, third gas flow controlled with a critical flow orifice

is added, but this flow is not measured or reported.

In general, flow problems can be divided into three categories:

1. Flow is too high

2. Flow is greater than zero, but is too low, and/or unstable

3. Flow is zero (no flow)

When troubleshooting flow problems, it is crucial to confirm the actual flow rate without
relying on the analyzer’s flow display. The use of an independent, external flow meter
to perform a flow check as described in Section 10.3.4 is essential.

The flow diagrams found in a variety of locations within this manual depicting the
T300/T300M in its standard configuration and with options installed can help in trouble-
shooting flow problems. For your convenience they are collected here.

06864D DCN7562

«
...
249
250
251
252
253
...
»

Summary of Contents for T300




























































































































































































































































































































































Reviews:

No comments

Related manuals for T300

Brand: M3S Pages: 40

Brand: Waterproof Pages: 10

Brand: Ocean Optics Pages: 43

Brand: Ocean Technology Systems Pages: 12

Brand: Ocean Reef Pages: 24

Brand: Sensia Pages: 16

Brand: Energic Plus Pages: 12

MTEK6000 Series

Brand: Metretek Pages: 81

Brand: Rodstation Pages: 28

QI-POWER-485-300

Brand: QEED Pages: 2

Brand: GREISINGER Pages: 20

Brand: SIGLENT Pages: 32

Brand: Clavia Pages: 13

Brand: Z-TRAUQ Pages: 10

Brand: PASCO Pages: 13

Simple Precision OWD

Brand: KAM Pages: 41

Brand: THORLABS Pages: 20

Brand: Barco Pages: 33

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands