TELEDYNE API T300 Operation Manual Download | Manualshive

Page: 255 / 347

background image

Teledyne API – Model T300/T300M CO Analyzer

Troubleshooting and Service

253

CO

2

Probe

Flow / Pressure

Sensor PCA

SAMPLE

PRESSURE

SENSOR

FLOW

SENSOR

Sample Gas

Flow Control

INSTRUMENT CHASSIS

SAMPLE GAS

INLET

EXHAUST

GAS OUTLET

Particulate Filter

PUMP

GFC Wheel

Housing

GFC Motor Heat Sync

SAMPLE CHAMBER

Figure 11-12: T300/T300M – Internal Pneumatics with CO

2

Sensor Option 67A

11.2.2.

TYPICAL SAMPLE GAS FLOW PROBLEMS

11.2.2.1.

FLOW IS ZERO

The unit displays a SAMPLE FLOW warning message on the front panel display or the
SAMPLE FLOW test function reports a zero or very low flow rate.

Confirm that the sample pump is operating (turning). If not, use an AC voltmeter to
make sure that power is being supplied to the pump if no power is present at the
electrical leads of the pump.

1. If AC power is being supplied to the pump, but it is not turning, replace the pump.

2. If the pump is operating but the unit reports no gas flow, perform a flow check as

described in Section 10.3.4.

3. If no independent flow meter is available:

•

Disconnect the gas lines from both the sample inlet and the exhaust outlet on
the rear panel of the instrument.

•

Make sure that the unit is in basic SAMPLE Mode.

•

Place a finger over an Exhaust outlet on the rear panel of the instrument.

•

If gas is flowing through the analyzer, you will feel pulses of air being expelled
from the Exhaust outlet.

06864D DCN7562

«
...
253
254
255
256
257
...
»

Summary of Contents for T300




























































































































































































































































































































































Reviews:

No comments

Related manuals for T300

Brand: YOKOGAWA Pages: 3

Brand: E Instruments Pages: 2

Brand: OHAUS Pages: 52

Brand: National Instruments Pages: 85

Brand: National Instruments Pages: 12

Brand: National Instruments Pages: 18

Brand: National Instruments Pages: 12

Brand: Omano Pages: 14

Brand: WalkLAB Pages: 16

Brand: Vega Pages: 20

Brand: Vega Pages: 16

Brand: Vega Pages: 2

Brand: JRC Pages: 308

Brand: ADDAC System Pages: 9

Brand: CG Pages: 7

Brand: Omega Pages: 20

Brand: Omega Pages: 4

Brand: ACCRETECH Pages: 104

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands