TELEDYNE API T300 Operation Manual Download | Manualshive

Page: 267 / 347

background image

Teledyne API – Model T300/T300M CO Analyzer

Troubleshooting and Service

265

11.5.7.6.

PRESSURE/FLOW SENSOR ASSEMBLY

The pressure/flow sensor PCA, located on the top of the absorption bench, can be
checked with a voltmeter using the following procedure which, assumes that the wiring
is intact, and that the motherboard and the power supplies are operating properly:

1. For Pressure related problems:

•

Measure the voltage across C1 - it should be 5 ± 0.25 VDC.

If not, then the board is bad.

•

Measure the voltage across TP4 and TP1.

•

With the sample pump disabled it should be 4500 mV ±250 mV.

•

With the pump energized it should be approximately 200 mV less.

If the voltage is incorrect, then S1, the pressure transducer is bad, the board is bad, or
there is a pneumatic failure preventing the pressure transducer from sensing the
absorption cell pressure properly.

2. For flow related problems:

•

Measure the voltage across TP2 and TP1 - it should be 10 ±0.25 VDC.

If not, then the board is bad.

•

Measure the voltage across TP3 and TP1:

•

With proper flow (800 sccm at the sample inlet) this should be approximately
4.5V (this voltage will vary with altitude).

•

With flow stopped (sample inlet blocked) the voltage should be approximately
1V.

If the voltage is incorrect, the flow sensor is bad, the board is bad, or there is a leak
upstream of the sensor.

06864D DCN7562

«
...
265
266
267
268
269
...
»

Summary of Contents for T300




























































































































































































































































































































































Reviews:

No comments

Related manuals for T300

Brand: Daewoo Pages: 2

SMatrix DMX2400

Brand: dallmeier Pages: 12

Network Card-MS

Brand: Eaton Pages: 26

Brand: J.P. Instruments Pages: 9

Brand: J.ASSY Pages: 13

Brand: R&S Pages: 733

Brand: R&S Pages: 369

Brand: T&D Pages: 2

Brand: T&D Pages: 2

Brand: Anritsu Pages: 29

Brand: VWR Pages: 44

Brand: Danfoss Pages: 16

Brand: Ibravebox Pages: 32

Brand: Omega Pages: 100

QI-POWER-485-300-LV

Brand: QEED Pages: 2

Proline Promag 10D

Brand: Endress+Hauser Pages: 28

Brand: HyQuest Solutions Pages: 25

Thruline 4020 Series

Brand: Bird Electronic Pages: 59

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands