TELEDYNE API T300 Operation Manual Download

Page: 272 / 347

Troubleshooting and Service

Teledyne API – Model T300/T300M CO Analyzer

270

11.5.10.2.

TROUBLESHOOTING ANALYZER/MODEM OR TERMINAL OPERATION

These are the general steps for troubleshooting problems with a modem connected to a
Teledyne API analyzer.

1. Check cables for proper connection to the modem, terminal or computer.

2. Check to make sure the DTE-DCE is in the correct position as described in Section

6.1.

3. Check to make sure the set up command is correct. See Section 8.3.

4. Verify that the Ready to Send (RTS) signal is at logic high. The T300/T300M sets

pin 7 (RTS) to greater than 3 volts to enable modem transmission.

5. Make sure the BAUD rate, word length, and stop bit settings between modem and

analyzer match. See Section 8.3.

6. Use the RS-232 test function to send “w” characters to the modem, terminal or

computer. See Section 8.3.

7. Get your terminal, modem or computer to transmit data to the analyzer (holding

down the space bar is one way); the green LED should flicker as the instrument is
receiving data.

8. Make sure that the communications software or terminal emulation software is

functioning properly.

Further help with serial communications is available in a separate manual “RS-232
Programming Notes” Teledyne API P/N 013500000.

11.5.11.

THE OPTIONAL CO

SENSOR

There are Two LEDs located on the CO

sensor PCA.

CPU

Analog

Output

To CO

Probe

OVDC 5VDC

GND +12 V

Power Supply

Connections

LED V8

(Red)

LED V9
(Green)

Serial I/O

(Not Used)

Figure 11-13: Location of Diagnostic LEDs onCO

Sensor PCA

•

Normal Operation: V8 is not lit – V9 is Blinking

•

Error State: Both LEDs are blinking.

Check to make sure that the cable to the CO

probe is properly connected.

06864D DCN7562

Summary of Contents for T300




























































































































































































































































































































































Search results

Summary of Contents for T300

Reviews:

Related manuals for T300

Brands by name

Popular brands

TELEDYNE API T300, Operation Manual

Search results

Summary of Contents for T300

Reviews:

Related manuals for T300

Brands by name

Popular brands