TELEDYNE API T300 Operation Manual Download | Manualshive

Page: 295 / 347

background image

Teledyne API – Model T300/T300M CO Analyzer

Theory of Operation

293

other photo emitters/detectors. These devices consist of a combination LED and
detector mounted so that the light emitted by the LED shines through the same mask on
the GFC Wheel that chops the IR beam.

IR Detection Ring

Segment Sensor Ring

M/R Sensor Ring

KEY:

Detection Beam shining
through MEASUREMENT
side of GFC Wheel

Detection Beam shining
through REFERENCE side
of GFC Wheel

Figure 12-11: GFC Light Mask

M/R

S

ENSOR

This emitter/detector assembly produces a signal that shines through a portion of the
mask that allows light to pass for half of a full revolution of the wheel. The resulting
light signal tells the analyzer whether the IR beam is shining through the measurement
or the reference side of the GFC Wheel.

S

EGMENT

S

ENSOR

Light from this emitter/detector pair shines through a portion of the mask that is divided
into the same number of segments as the IR detector ring. It is used by the
synchronous/demodulation circuitry of the analyzer to latch onto the most stable part of
each measurement and reference IR pulse.

06864D DCN7562

«
...
293
294
295
296
297
...
»

Summary of Contents for T300




























































































































































































































































































































































Reviews:

No comments

Related manuals for T300

Brand: HANYOUNG NUX Pages: 4

Brand: jenway Pages: 30

Brand: National Meter & Automation Pages: 24

Brand: Lakeshore Pages: 2

Brand: Kamstrup Pages: 4

Brand: Panasonic Pages: 72

KW9M Eco-Power Meter

Brand: Panasonic Pages: 2

Brand: ACECO Pages: 2

Brand: Keithley Pages: 32

Brand: MICRO-EPSILON Pages: 82

Brand: Hanna Instruments Pages: 28

Brand: JensPrima Pages: 20

SoundExpert LxT

Brand: Larson Davis Pages: 307

Brand: Zhengzhou Minghe Electronic Technology Pages: 7

Brand: Mid-West Pages: 14

Brand: Omega Pages: 24

Brand: wtw Pages: 70

Brand: Tektronix Pages: 29

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands