TELEDYNE API T300 Operation Manual Download

Page: 71 / 347

Teledyne API – Model T300/T300M CO Analyzer

Getting Started

Table 3-13: Possible Warning Messages at Start-Up

Message

MEANING

ANALOG CAL WARNING

The instrument's A/D circuitry or one of its analog outputs is not calibrated.

BENCH TEMP WARNING

Optical bench temperature is outside the specified limits.

BOX TEMP WARNING

The temperature inside the T300/T300M chassis is outside the specified limits.

CANNOT DYN SPAN

Remote span calibration failed while the dynamic span feature was set to
turned on.

CANNOT DYN ZERO

Remote zero calibration failed while the dynamic zero feature was set to turned
on.

CONFIG INITIALIZED

Configuration was reset to factory defaults or was erased.

DATA INITIALIZED

DAS data storage was erased.

PHOTO TEMP WARNING

Photometer temperature outside of warning limits.

REAR BOARD NOT DET

Motherboard was not detected during power up.

RELAY BOARD WARN

CPU is unable to communicate with the relay PCA.

SAMPLE FLOW WARN

The flow rate of the sample gas is outside the specified limits.

SAMPLE PRESS WARN

Sample pressure outside of operational parameters.

SAMPLE TEMP WARN

The temperature of the sample gas is outside the specified limits.

SOURCE WARNING

The IR source may be faulty.

SYSTEM RESET

The computer was rebooted.

WHEEL TEMP WARNING

The Gas Filter Correlation Wheel temperature is outside the specified limits.

Typically clears 45 minutes after power up.

Clears the next time successful zero calibration is performed.

Clears the next time successful span calibration is performed.

Table 3-14 lists brief descriptions of the warning messages that may occur during start
up for T300 analyzers with optional second gas options or alarms installed.

06864D DCN7562

Summary of Contents for T300




























































































































































































































































































































































Search results

Summary of Contents for T300

Reviews:

Related manuals for T300

Brands by name

Popular brands

TELEDYNE API T300, Operation Manual

Search results

Summary of Contents for T300

Reviews:

Related manuals for T300

Brands by name

Popular brands