TELEDYNE API T300 Operation Manual Download | Manualshive

Page: 72 / 347

background image

Getting Started

Teledyne API – Model T300/T300M CO Analyzer

70

Table 3-14:

Possible Startup Warning Messages – T300 Analyzers with Options

Message

Meaning

O2 CELL TEMP WARN

1

O

2

sensor cell temperature outside of warning limits.

IZS TEMP WARNING

2

On units with IZS options installed: The permeation tube temperature is outside
of specified limits.

O2 ALARM 1 WARN

1, 4

O

2

Alarm limit #1 has been triggered.

4

O2 ALARM 2 WARN

1, 4

O

2

Alarm limit #2 has been triggered.

4

CO2 ALARM 1 WARN

3, 4

CO

2

Alarm limit #1 has been triggered.

4

CO2 ALARM 2 WARN

3, 4

`

CO

2

Alarm limit #2 has been triggered.

4

SO2 ALARM1 WARN

4

SO

2

Alarm limit #1 has been triggered.

4

SO2 ALARM2 WARN

4

SO

2

Alarm limit #2 has been triggered.

4

1

Only appears when the optional O

2

sensor is installed.

2

Only appears when the optional internal zero span (IZS) option is installed.

3

Only appears when the optional CO

2

sensor is installed.

4

Only Appears when the optional gas concentration alarms are installed

3.4.3.

FUNCTIONAL CHECKS

After the analyzer’s components have warmed up for at least 60 minutes, verify that the
software properly supports any hardware options that were installed: navigate through
the analyzer’s software menus, see the menu trees described in Appendix A.

Then check to make sure that the analyzer is functioning within allowable operating
parameters:

•

Scroll the test functions viewable from the analyzer’s front panel.

•

These functions are also useful tools for diagnosing performance problems with your
analyzer (see Section 11.1.2).

•

The enclosed Final Test and Validation Data Sheet (P/N 04271) lists these values
as they were before the instrument left the factory.

To view the current values of these parameters press the following control button
sequence on the analyzer’s front panel. Remember that until the unit has completed its
warm-up these parameters may not have stabilized.

06864D DCN7562

«
...
70
71
72
73
74
...
»

Summary of Contents for T300




























































































































































































































































































































































Reviews:

No comments

Related manuals for T300

Brand: Atomos Pages: 4

Brand: Abbott Pages: 296

Brand: Campbell Pages: 362

Brand: Campbell Pages: 60

Brand: Campbell Pages: 116

Brand: Campbell Pages: 30

Brand: Campbell Pages: 55

Brand: Ebtron Pages: 5

Brand: Okolab Pages: 4

Brand: janitza Pages: 12

Brand: janitza Pages: 84

Brand: janitza Pages: 6

Brand: janitza Pages: 14

Brand: janitza Pages: 98

NANOCOLOR Advance

Brand: Macherey-Nagel Pages: 45

Brand: Wagner Meters Pages: 17

Brand: X-Rite Pages: 45

Brand: X-Rite Pages: 22

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands