Teledyne Lecroy PP023 User Manual Download

Page: 11 / 12

User Manual

EAR99 technology subject to restrictions on copyrights page.

Replaceable Parts

Item

Part Number

Description

QTY

PK5-2.5MM-101

Ground Lead with Alligator Clip

PK5-2.5MM-102

Rigid Probe Tip (1 installed standard)

PK5-2.5MM-103

Short Collar (installed standard)

PK5-2.5MM-104

Sprung Hook

PK5-PK6-001

Trimmer Tool

PK5-2.5MM-105

Long Collar

PK5-2.5MM-106

IC Tip Insulators (Black, Brown, Blue, Green, Gray)

PK5-2.5MM-107

Tip Insulator 2.5mm

PK5-2.5MM-108

Probe Tip Cover

PK5-2.5MM-109

BNC Adapter 2.5mm

PK5-2.5MM-110

Swivel Ground Lead

PK5-2.5MM-111

Swivel Ground Lead Adapter

PK5-2.5MM-112

Ground Spring

PK5-2.5MM-113

PCB Adapter

PK5-2.5MM-114

Spring Tip

PK5-PK6-002

Color Coding Rings (2 ea. yellow, red, green, blue)

Standard Accessory Replacement Kit part number is PKIT5-2.5MM-101.

Summary of Contents for PP023













Search results

Summary of Contents for PP023

Reviews:

Related manuals for PP023

Brands by name

Popular brands

Teledyne Lecroy PP023, User Manual

Search results

Summary of Contents for PP023

Reviews:

Related manuals for PP023

Brands by name

Popular brands