background image

4. PRESET menu                                           

Press the PRESET button of remote control or press the MENU button of TV to select the PRESET menu, 

you may press P+/P- button to choose each item. The selected item will be indicated by an arrow and will be red in 

colour. The rest of the menu will be green. You can change the value of selected item by pressing V+/V- button and 

you can use buttons 0-9 and -/--/--- to select a channel. At 

AUTO-SEARCH

, press V+/V- button and the TV will 

search all the active channels in your area and store them into memory. Before AUTO-SEARCH, if you select 

SYSTEM menu, at the item 

COLOR-SYS

, press V+/V- button to set it to AUTO, so that the colour system will 

be automatically selected.   

At the item 

BAND

, press V+/V- button to select band (V-L, V-H, U) which you start to adjust. 

At the item 

FINE

(fine tuning) or

SEMI-SEARCH

, it can search higher frequency by pressing V+  button 

or lower frequency by pressing V- button . In this process, the striped symbol turns red and the erect block changes 

into an arrow referring to the direction of tuning. In SEMI-SEARCH mode when it has found a program, the search 

stops. In FINE mode, when you don't press V+/V- button, the search stops. When the search stops, the striped 

symbol turns green and the arrow changes into an erect block. The new program will be stored automatically into 

the memory. 

If you want to delete any program, you can select the POSITION item to set the program number and change 

the REMEMBER item to OFF. This program will be deleted. 

The PRESET menu displays on the screen is as follows:   
                                                                 
 
                                       
                                      PRESET 

   
                               

      POSITION                0 

                           

 

      REMEMBER            ON 

                       BAND            V-L 
                                              FINE 
                                              SEMI-SEARCH 
                                              AUTO-SEARCH 
 
 

 

 

 

5. PICTURE menu 

  Press the PICTURE button on the remote control or the menu button on the TV to select the PICTURE 

menu. Press the PICTURE button continuously or press P+/P- button up/down to choose each item, the chosen item 

indicated by an arrow now is red

the other items are all green .You can now change the value of the setting. The 

display of striped symbol and number below the screen refers to the value of the present item                  

relevantly. When the input signal is PAL system

color system is AUTO or is forced into PAL system and the 

picture is coloured

the item of TINT will display on the screen

 

  All Adjustments made in the PICTURE menu will be stored automatically. If no adjustments are made for 

10 seconds menu is automatically exited. 

 

 

 

 

 

 

 

 

Summary of Contents for TTV-149












Reviews: