background image

IRIS/SIMPO Repeater TFT - Addressable Fire Alarm Repeater Panel 

– Installation & Programming Manual 

 

 

 

 
 
 
 
 
 
 
 
 
 
 
 
 
 
GUARANTEE 

The guarantee terms are determined by the serial number (barcode) of the electronic device! 

During the guarantee period the manufacturer shall, at its sole discretion, replace or repair any defective product when it is returned to the factory. All 
parts  replaced  and/or  repaired  shall  be  covered  for  the  remainder  of  the  original  guarantee,  or  6  months,  whichever  period  is  longer.  The  original 
purchaser shall immediately send manufacturer a written notice of the defective parts or workmanship. 

 

INTERNATIONAL GUARANTEE 

Foreign customers shall possess the same guarantee rights as those any customer in Bulgaria, except that manufacturer shall not be liable for any 
related customs duties, taxes or VAT, which may be payable. 

 
GUARANTEE PROCEDURE 

The guarantee will be granted when the appliance in question is returned. The guarantee period and the period for repair are  determined in advance. 
The manufacturer shall not accept any product, of which no prior notice has been received via the RAN form at: 

http://teletek-electronics.com/en/ran-

form

 

The setup and programming included in the technical documentation shall not be regarded as defects. Teletek Electronics bears no responsibility for 
the loss of programming information in the device being serviced. 

 

CONDITIONS FOR WAIVING THE GUARANTEE 

This guarantee shall apply to defects in products resulting only from improper materials or workmanship, related to its normal use. It shall not cover: 

 

Devices with destroyed serial number (barcode); 

 

Damages resulting from improper transportation and handling; 

 

Damages caused by natural calamities, such as fire, floods, storms, earthquakes or lightning; 

 

Damages caused by incorrect voltage, accidental breakage or water; beyond the control of the manufacturer; 

 

Damages caused by unauthorized system incorporation, changes, modifications or surrounding objects; 

 

Damages caused by peripheral appliances unless such peripheral appliances have been supplied by the manufacturer; 

 

Defects caused by inappropriate surrounding of installed products; 

 

Damages caused by failure to use the product for its normal purpose;  

 

Damages caused by improper maintenance; 

 

Damages resulting from any other cause, bad maintenance or product misuse. 

In  the  case  of  a  reasonable  number  of  unsuccessful  attempts  to  repair  the  product,  covered  by  this  guarantee,  the  manufacture

r’s liability shall be 

limited to the replacement of the product as sole compensation for breach of the guarantee. Under no circumstances shall the manufacturer be liable 
for  any special,  accidental  or consequential  damages,  on the  grounds  of  breach  of  guarantee,  breach  of  agreement,  negligence,  or  any  other  legal 
notion. 

 

WAIVER 

This Guarantee shall contain the entire guarantee and shall be prevailing over any and all other guarantees, explicit or implicit (including any implicit 
guarantees on behalf of the dealer, or adaptability to specific purposes), and over any other responsibilities or liabilities on behalf of the manufacturer. 
The manufacturer does neither agree, nor empower, any person, acting on his own behalf, to modify, service or alter this Guarantee, nor to replace it 
with another guarantee, or another liability with regard to this product. 

 
UNWARRANTED SERVICES 

The  manufacturer  shall  repair  or  replace  unwarranted  products,  which  have  been  returned  to  its  factory,  at  its  sole  discretion  under  the  conditions 
below.  The  manufacturer  shall  accept  no  products  for  which  no  prior  notice  has  been  received  via  the  RAN  form  at: 

http://teletek-

electronics.com/en/ran-form

. 

The  products,  which  the  manufacturer  deems  repairable,  will  be  repaired  and  returned.  The  manufacturer  has  prepared  a  price  list  and  those 
products, which can be repaired, shall be paid for by the Customer. The devices with unwarranted services carry 6 months guarantee for the replaced 
parts. 
The closest equivalent product, available at the time, shall replace the products, the manufacturer deems un-repairable. The current market price shall 
be charged for every replaced product.  

 

STANDARDS AND CONFORMITY 

 

Conforms and approved in accordance with CPR (Construction Products Regulation). 
 

DOCUMENTATION FEEDBACK 

 

If you have any comments or suggestions on our products’ manuals or installation instructions you can email us on: info@teletek-electronics.bg 
Your feedback on product documentation will help us to improve the contents of our manuals and stickers and keep them up-to-date. 
Please, include in your feedback email the product name, the revision of the manual or instruction (8-digit number with Revision and date of issue) 
and the page number. 

  21

 

                                                                         1293 

                                                                                  DoP No: 138 

 

Teletek Electronics JSC 

Bulgaria, Sofia 1407, 

14А Srebarna Str., Tel.: +359 2 9694 800, Fax: +359 2 962 52 13 

e-mail

info@teletek-electronics.bg

 

 

IRIS/SIMPO Repeater  

Intended for use in fire detection and fire alarm systems in and around buildings. 

 

Summary of Contents for TFT





























Reviews: