background image

1.4

Safety Information

1

INTRODUCTION

1.4

Safety Information

START BY READING THESE IMPORTANT

SAFETY INSTRUCTIONS AND NOTES

In these instructions the word “product” refers to the Compact 2A and all of its approved parts and ac-
cessories. NOTE: These instructions do not and cannot provide for every contingency that may arise
in connection with the installation, operation, or maintenance of this product. Should you require
further assistance, please contact Televac at the email address found in the footer of this manual.

This product has been designed and tested to offer reasonably safe service provided in it is installed,
operated and serviced in strict accordance with these safety instructions.

These safety precautions must be observed during all phases of operation, installation, and service
of this product. Failure to comply with these precautions or with specific warnings elsewhere in this
manual violates safety standards of design, manufacture, and intended use of the instrument. Televac
disclaims all liability for the customer’s failure to comply with these requirements.

ˆ

READ instructions – Read all safety and operating instructions before operating the product.

ˆ

RETAIN instructions – Retain the Safety and Operating Instructions for future reference.

ˆ

HEED warnings – Adhere to all warnings on the product and in the operating instructions.

ˆ

FOLLOW instructions – Follow all operating and maintenance instructions.

ˆ

ACCESSORIES – Do not use accessories not recommended in this manual as they may require a
technician to restore the product to its normal operation.

The Compact 2A qualifies as a Safety Extra-Low Voltage (SELV) device. As such, it represents little to
no hazard concerning electrical shock or burns.

Do not substitute parts or modify instrument. Because of the danger on introducing addi-
tional hazards, do not install substitute parts or perform any unauthorized modifications
to the product. Return the product to Televac for service and repair to ensure that safety
features are maintained. Do not use this product if it has unauthorized modifications

email: sales@frederickscompany.com

tel: +1 215 947 2500

web: frederickscompany.com

comp_2a_im rev -

3 of 7

Summary of Contents for Compact 2A









Reviews: