background image

3

PART NUMBERS

3

Part Numbers

Table 2: Controller, Cable, and Sensor Part Numbers

MV2A Controller

2-7900-071

2A Sensor 1/8” NPT Nickel-Plated Brass

2-2100-10

2A Sensor Stainless Steel 1/8” NPT

2-2126-001

2A Sensor Stainless Steel NW16 (DN16 ISO-KF)

2-2126-030

2A Sensor Stainless Steel NW25 (DN25 ISO-KF)

2-2126-031

2A Sensor Stainless Steel 8-VCO Male

2-2126-040

2A Sensor Stainless Steel 8-VCO Female

2-2126-041

2A Sensor Stainless Steel 8-VCR Male

2-2126-042

2A Sensor Stainless Steel 8-VCR Female

2-2126-043

2A Sensor Stainless Steel 4-VCR Male

2-2126-044

2A Sensor Stainless Steel 4-VCR Female

2-2126-045

2A Sensor Stainless Steel 1.33” CF (DN16 ISO-CF-F)

2-2126-050

2A Sensor Stainless Steel 2.75” CF (DN40 ISO-CF-F)

2-2126-052

3 ft Cable

2-9800-076

10 ft Cable

2-9800-077

20 ft Cable

2-9800-078

35 ft Cable

2-9800-079

50 ft Cable

2-9800-080

VacuMini 2A Sensor

2-2100-102

NASA 2A Miniature Sensor

2-2100-31

Contact Fredericks Company for further sensor flange types and cable lengths.

email: sales@frederickscompany.com

tel: +1 215 947 2500

web: frederickscompany.com

mv2a_im rev B

6 of 6

Summary of Contents for MV2A








Reviews: