background image

TELEX SAFE-1000  

 

 

Page 6 

 

SYSTEM PROGRAMMING 
 

The SAFE-1000 System uses the same basic programming steps in the 
Receiver and Transmitters. Learning these basic steps early will save time 
and effort. 
 
SCREENS: Computer controlled screens will advance or return   
                    automatically. The software version screens will stay on for   
                    about 3 seconds after power is applied. To see them again, you  
                    must turn power OFF and then ON again. 
MENU:       Pressing this “key” once will advance the current screen to the   
                    next screen.This key will also perform a “SET” operation as the  
                    current screen is left. To review the various screen status, press  
                    the key to advance screens. No change to screens will occur  
                    unless the “SET” Key is pressed.  
SET:          This key is used to initiate any change to the screen currently  
                   being viewed. Flashing (blinking) characters will be seen after  
                   the SET Key is pressed. The flashing characters can be changed  
                   by use of the “Arrow” Keys or accepted as is by using the SET   
                   key. Use the MENU Key to exit the current screen. Exiting a  
                   screen with the MENU Key terminates any flashing operation.

 

ARROW:   These keys are used to make changes to the screen currently  
                   being viewed. The keys are not active until SET is pressed, with  
                   one exception. When the SQUELCH screen is displayed, the  
                   squelch bar can be changed with the Arrow Keys without  
                   pressing SET. Exiting the SQUELCH Screen by pressing  
                   MENU saves the setting. 
Power:         Removing power from any unit saves the last operation of all  
                    screens. 
Other:           All other unit controls are manually operated. 

 

 
 

 
 
 
 
 

Summary of Contents for SAFE-1000











Reviews: