Telit Wireless Solutions EZ10 Series Product Description Download

Page: 2 / 74

Telit EZ10-GPRS/-PCS

Product Description

80269ST10014a, Rev. 3 – 26/09/05

Reproduction forbidden without written authorization by Telit Communications S.p.A.

Page 2 of 74

Contents

OVERVIEW............................................................................................................................... 6

GENERAL PRODUCT DESCRIPTION .................................................................................... 9

2.1

Dimensions .......................................................................................................................... 9

2.2

Weight .................................................................................................................................. 9

2.3

Installation ........................................................................................................................... 9

2.4

Environmental requirements ........................................................................................... 10

2.4.1

Temperature range...................................................................................................... 10

2.5

EZ10 Interfaces.................................................................................................................. 11

2.5.1

Product Versions Identification - Documentation ........................................................ 12

2.5.2

Supply voltage requirements....................................................................................... 14

2.5.3

POWER / GPIO3 Connector ....................................................................................... 16

2.5.4

RJ11 (AUX) connector ................................................................................................ 16

2.5.5

Audio Interface Specification....................................................................................... 19

2.5.6

GPIO Interface Specification ....................................................................................... 20

2.5.7

RS232 standard interface connector........................................................................... 20

2.5.8

SIM Interface Characteristics ...................................................................................... 21

2.5.9

Insertion and Removal of the SIM ............................................................................... 21

2.5.10

Antenna Output ........................................................................................................... 21

2.6

Operating Frequency ........................................................................................................ 23

2.7

Transmitter output power................................................................................................. 23

2.8

Reference sensitivity ........................................................................................................ 23

2.9

User Interface .................................................................................................................... 24

2.9.1

Switching the EZ10 Terminals ON and OFF ............................................................... 24

2.9.2

Functions of the RS232 Serial Interface...................................................................... 25

2.9.3

Functions of the RJ11 Interface .................................................................................. 26

2.9.4

Speech Coding............................................................................................................ 27

2.9.5

SMS............................................................................................................................. 27

2.9.6

Real Time Clock and Alarm......................................................................................... 27

2.9.7

Data/fax transmission.................................................................................................. 27

2.9.8

Local security management ........................................................................................ 27

2.9.9

Call control .................................................................................................................. 27

2.9.10

Phonebook .................................................................................................................. 27

2.9.11

Characters management............................................................................................. 28

2.9.12

SIM related functions................................................................................................... 28

2.9.13

Call status indication ................................................................................................... 28

2.9.14

LED Indicators............................................................................................................. 28

Summary of Contents for EZ10 Series











































































Search results

Summary of Contents for EZ10 Series

Reviews:

Related manuals for EZ10 Series

Brands by name

Popular brands

Telit Wireless Solutions EZ10 Series, Product Description

Search results

Summary of Contents for EZ10 Series

Reviews:

Related manuals for EZ10 Series

Brands by name

Popular brands