Telit Wireless Solutions LE910C series At Commands Reference Manual Download | Manualshive

Page: 1105 / 1904

Page 1105

background image

LE910Cx AT Commands Reference Guide

80502ST10950A Rev. 14

Page 1105 of 1904

2022-03-04

Not Subject to NDA

0

: battery is exhausted, or ME does not have a

battery connected

25 : battery charge remained is estimated to be

25%

50 : battery charge remained is estimated to be

50%

75 : battery charge remained is estimated to be

75%

100 : battery is fully charged

<bcs>=1 indicates that the battery charger supply is inserted and
the battery is being recharged if necessary with it. Supply for ME
operations is taken anyway from VBATT pins.

Without battery/power connected on VBATT pins or during a
power fault the unit is not working, therefore values <bcs>=2 and
<bcs>=3 will never appear.

<bcl> indicates battery charge level only if battery is connected
and charger is not connected.

AT+CBC=?

Test command returns parameter values supported as a compound
value.

The ME does not make differences between being powered by a
battery or by a power supply on the VBATT pins, so it is not possible
to distinguish between these two cases.

«
...
1103
1104
1105
1106
1107
...
»

Summary of Contents for LE910C series

















































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for LE910C series

Brand: WEARHAUS Pages: 62

Brand: Tenda Pages: 57

TL-WR541G - Wireless Router

Brand: TP-Link Pages: 91

Brand: EAS Electric Pages: 110

Brand: sauter Pages: 8

Jetpack MiFi 4510L

Brand: Verizon Pages: 88

Brand: Modecom Pages: 48

WAP54G - Wireless-G Access Point

Brand: Linksys Pages: 84

TEW-434APB - 54Mbps Wireless G PoE Access Point

Brand: TRENDnet Pages: 2

Brand: Billion Pages: 130

Brand: Rosewill Pages: 6

Brand: ADS-tec Pages: 2

Brand: Draytek Pages: 18

Brand: Broadxent Pages: 27

Brand: Proxim Pages: 72

Brand: High-Flying Pages: 17

MultiModem rCell MTCBA-H3-EN3-P1

Brand: Multitech Pages: 71

MultiModem rCell

Brand: Multitech Pages: 100

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands