Telit Wireless Solutions LE910C series At Commands Reference Manual Download

Page: 1234 / 1904

Page 1234

LE910Cx AT Commands Reference Guide

80502ST10950A Rev. 14

Page 1234 of 1904

2022-03-04

Not Subject to NDA

#SCFGEXT: <connId

. . .

#SCFGEXT:<connId

conMax

>,<srMode>,<dataMode>,<keepalive>,

AT#SCFGEXT=?

Test command returns the range of supported values for all the sub parameters.

•

Socket 1 set with data view sring, text data mode, a keepalive time of

30 minutes and listen auto-response set.

Socket 3 set with data amount sring, hex recv data mode, no
keepalive and listen auto-response not set.

Socket 4 set with hex recv and send data mode.

AT#SCFGEXT?
#SCFGEXT: 1,2,0,30,1,0
#SCFGEXT: 2,0,0,0,0,0
#SCFGEXT: 3,1,1,0,0,0
#SCFGEXT: 4,0,1,0,0,1
...
...
OK

«
...
1232
1233
1234
1235
1236
...
»

Summary of Contents for LE910C series

















































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for LE910C series

Reviews:

Related manuals for LE910C series

Brands by name

Popular brands

Telit Wireless Solutions LE910C series, At Commands Reference Manual

Search results

Summary of Contents for LE910C series

Reviews:

Related manuals for LE910C series

Brands by name

Popular brands