Telit Wireless Solutions LE910C series At Commands Reference Manual Download

Page: 1489 / 1904

Page 1489

LE910Cx AT Commands Reference Guide

80502ST10950A Rev. 14

Page 1489 of 1904

2022-03-04

Not Subject to NDA

<tac>

mixed

Tracking Area Code. if #CSURVF last setting
is 0, <tac> is a decimal number, else it is a 4-
digits hexadecimal number

<pci>

mixed

physical cell identifier; if #CSURVF last
setting is 0, <pci> is a decimal number, else
it is a 4-digits hexadecimal number

<cellStatus> integer

N/A

it is the cell status

Values:

0 : C0 is a suitable cell (CELL_SUITABLE).

1 : the cell is low priority based on the received system

information (CELL_LOW_PRIORITY).

2 : the cell is forbidden (CELL_FORBIDDEN).

3 : the cell is barred based on the received system

information (CELL_BARRED).

4 : the cell <rxLev> is low (CELL_LOW_LEVEL).

5 : none of the above e.g. exclusion timer running, no

BCCH available…etc.. (CELL_OTHER).

<rsrp>

integer

Reference Signal Received Power

<rsrq>

integer

Reference Signal Received Quality

<bandwidth> integer

E-UTRA bandwidth of serving cell

The bandwidth, <bandwidth>, of LTE neighbor cells(intra/inter) cannot be
appeared.

The value of <cellId> for LTE serving cell is replaced to cell identifier.

<pci> is added with name of phyCellId and the cellId name for neighbor
cells were replaced to phyCellId.

«
...
1487
1488
1489
1490
1491
...
»

Summary of Contents for LE910C series

















































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for LE910C series

Reviews:

Related manuals for LE910C series

Brands by name

Popular brands

Telit Wireless Solutions LE910C series, At Commands Reference Manual

Search results

Summary of Contents for LE910C series

Reviews:

Related manuals for LE910C series

Brands by name

Popular brands