Telit Wireless Solutions LE910C series At Commands Reference Manual Download

Page: 292 / 1904

Page 292

LE910Cx AT Commands Reference Guide

80502ST10950A Rev. 14

Page 292 of 1904

2022-03-04

Not Subject to NDA

if a connection has been set up issuing either #SKTD or #SKTOP,
then AT&D1 has the same effect as AT&D2.

If AT&D2 been issued and the DTR has been tied Low, auto
answering is inhibited and it is possible to answer only issuing
command ATA.

If parameter is omitted, the command has the same behavior of
AT&D0.

&D3, &D4 are used for the backward compatibility, the command
has the same behaviour of AT&D0.

Summary of Contents for LE910C series

















































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for LE910C series

Reviews:

Related manuals for LE910C series

Brands by name

Popular brands

Telit Wireless Solutions LE910C series, At Commands Reference Manual

Search results

Summary of Contents for LE910C series

Reviews:

Related manuals for LE910C series

Brands by name

Popular brands