Telit Wireless Solutions LE910C series At Commands Reference Manual Download

Page: 943 / 1904

Page 943

LE910Cx AT Commands Reference Guide

80502ST10950A Rev. 14

Page 943 of 1904

2022-03-04

Not Subject to NDA

string

string for user
confirmation stage

string

string containing called
numbers

This section is dedicated to the following proactive commands:

<cmdType>=17 (SEND SS)
<cmdType>=18 (SEND USSD)
<cmdType>=19 (SEND SHORT MESSAGE)
<cmdType>=20 (SEND DTMF)
<cmdType>=32 (PLAY TONE)

the response format:

#STGI: <cmdType>[,<alphaIdentifier>]

Name

Type Default

Description

<alphaIdentifier> string

optional text provided by the
SIM/USIM device in ASCII format

<cmdType>=33 (DISPLAY TEXT)

the response format:

#STGI: 33,<cmdDetails>[,<text>]

Name

Type Default

Description

<cmdDetails> hex

N/A

a bit mask where each bit position,
according to its value, has a specific
meaning:

bit 0:
0 - normal priority
1 - high priority

bits 1-6:
reserved for future use

Summary of Contents for LE910C series

















































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for LE910C series

Reviews:

Related manuals for LE910C series

Brands by name

Popular brands

Telit Wireless Solutions LE910C series, At Commands Reference Manual

Search results

Summary of Contents for LE910C series

Reviews:

Related manuals for LE910C series

Brands by name

Popular brands