background image

 

9

5 Module status 

5.1 LED signals 

 

Green blinks slowly, 
Red is not lit 

GPRS OK 

Green is continuously lit 

IP reporting in progress 

Green blinks fast 

GSM reporting in progress 

Red blinks 3 times  

Reporting failed 

Red is continuously lit 

Trouble 

 

5.2 Status 

On the 

“Status”

 page the connected ecoLINE SIA IP Adapter’s state can be monitored 

(version information, system timer, GSM status, GPRS network, communication, event 
monitoring). 
 
Available status information:  
 

 

Version information:

 

- Type: 

type of the module 

- Hardware 

version:

 version of the hardware 

- Firmware 

version:

 version of the firmware 

 

 

System timer: 
- Date/time: 

internal clock of the connected module

 

- Uptime: 

elapsed time since the last module restart

 

 

 

GSM status: 
- GSM 

signal: 

current GSM signal strength 

- Uptime: 

elapsed time since the last GSM network connection

 

 

 

GPRS network: 
- Module 

IP: 

the module’s actual IP address 

- Uptime: 

elapsed time since the last GPRS network connection 

- Data 

traffic: 

data traffic since the last GPRS network connection

 

-  Number of connections: 

actual number of the IP connections 

 

 

Communication: 
- Line 

status: 

actual line state 

 

- Dialed 

number: 

the last number dialed by the alarm control panel

 

- Protocol:

 the last used protocol

 

 

 

Event monitoring:

 list of the latest Contact ID events

 

Summary of Contents for ecoLINE SIA IP












Reviews: