Section 4 INSTALLATION &
BASIC OP
57
NT1 will automatically be disabled. The NT1 power may come from the Zephyr, so no
additional power supply is needed. Some telephone sets may be powered from the
Zephyr.
The S/T cable is has larger plugs than a normal modular phone cable, using 8- pin RJ-
45s. Four of the wires are used for the S interface and two are used to convey power
from the Zephyr to the NT1.
The S/T Only Interface (Europe and Elsewhere)
The Zephyr connects to the NT1 at one of the TERMINAL jacks. Use only an 8-
conductor cable.
Unlike the USA version, this ISDN interface does not provide power to the NT1 and it
must be provided independently.
TA
Zephyr S/T ISDN Interface
NT1
S/T
To
Telco Line
The usual set-up outside the USA. The S/T jack is connected
to the NT1 provided by the telephone authority.
HOT TIP!
NT1s often have a reset button which may be pressed to re-
start the NT1 and re-initialize the Telco connection, in the
event of trouble. The Zephyr will sense the reset and will
respond by also re-initializing its part of the ISDN connection.
However, any connection in progress will be lost when this
happens.
IMPORTANT!
In this case, the NT1 will be powered by the Telco. If your
Zephyr’s terminal adapter does not show the Euro telecom
approval symbol (looks like 2 hockey sticks in a circle) you
should contact Telos Systems customer support before
proceeding. This is because the Zephyr’s built in supply and
the power supply from the NT1 can conflict and cause damage
to the Zephyr, NT1, or both.
Summary of Contents for Zephyr
