background image

TS1000BS Base Station User Menu

16

3.2 INSPECTION

Inspect the equipment thoroughly as soon as possible after delivery. If any part of
the equipment has been damaged in transit, report the extent of damage to the
transportation company immediately.

CAUTION

Station contains CMOS devices. Good
troubleshooting and installation techniques require
proper grounding of personal prior to handling
equipment.

3.3 PLANNING THE INSTALLATION

Since a good installation is important to obtain the best possible performance of the
communications system, carefully plan the installation before actual work is started.
Location of the station in relation to power, control lines, the antenna, and
convenience and access for servicing should be considered. The cabinet
dimensional detail diagrams show the size the various cabinets for planning the
space requirements. Read the entire procedure and the many suggestions offered to
help you plan your installation. Make sure all tools, equipment, and facilities are
available when the installation is begun.

3.4 INSTALLATION

Station can be installed in indoor or outdoor. The cabinet should be located on a
solid, level surface convenient to the power source and the RF transmission line.
The RF transmission line should be kept as short as possible to minimize line

Summary of Contents for TS1000BS





















Reviews: