background image

 
 

  

TMP

 

Oil Furnaces

 – 

Furnace Manual

 

670-000-004/1010  

21

 

Handling ceramic fiber and fiberglass materials 

 

HANDLING OR REMOVAL OR COMBUSTION CHAMBER 

 

The combustion chamber in this product contains ceramic fiber materials. 
Ceramic fiber can be converted to cristobalite in very high temperature 
applications. The International Agency for Research on Cancer (IARC) has 
concluded, “Crystalline silica inhaled in the form of quartz or cristobalite from 
occupational sources is carcinogenic to humans (Group 1)”. 

 

„

  Avoid breathing dust and contact with skin and eyes. 

 

Use NIOSH certified dust respirator (N95). This type of respirator is based on the OSHA 
requirements for cristobalite at the time this document was written. Other types of respirators 
may be needed depending on the job site conditions. Current NIOSH recommendations can 
be found on the NIOSH web site at 

http://www.cdc.gov/niosh/homepage.html

NIOSH 

approved respirators, manufacturers, and phone numbers are also listed on this web site. 

 

Wear long-sleeved, loose fitting clothing, gloves, and eye protection. 

„

  Apply enough water to the combustion chamber lining to prevent airborne dust. 

„

  Remove combustion chamber lining from the furnace and place it in a plastic bag for disposal. 

„

  Wash potentially contaminated clothes separately from other clothing. Rinse clothes washer 

thoroughly. 

 

NIOSH stated First Aid. 

„

  Eye: Irrigate immediately 

„

 Breathing: 

Fresh 

air. 

 
 
 
 
 
 
 

HANDLING OR REMOVAL OF FIBERGLASS WOOL – OR –  

INSTALLATION OF FIBERGLASS WOOL OR COMBUSTION CHAMBER: 

 

This product contains fiberglass jacket insulation and ceramic fiber materials in 
combustion chamber. Airbone fibers from these materials have been listed by 
the State of California as a possible cause of cancer through inhalation. 

 

„

  Avoid breathing dust and contact with skin and eyes. 

 

Use NIOSH certified dust respirator (N95). This type of respirator is based on the OSHA 
requirements for fiberglass wool at the time this document was written. Other types of 
respirators may be needed depending on the job site conditions. Current NIOSH 
recommendations can be found on the NIOSH web site at 

http://www.cdc.gov/niosh/homepage.html

NIOSH approved respirators, manufacturers, and 

phone numbers are also listed on this web site. 

 

Wear long-sleeved, loose fitting clothing, gloves, and eye protection. 

„

  Operations such as sawing, blowing, tear out, and spraying may generate airbone fiber 

concentration requiring additional protection. 

„

  Wash potentially contaminated clothes separately from other clothing. Rinse clothes washer 

thoroughly. 

 

NIOSH stated First Aid. 

„

  Eye: Irrigate immediately 

„

 Breathing: 

Fresh 

air. 

 

Summary of Contents for TMP-105





























Reviews: