background image

7

UNIT DAMAGE HAZARD

Failure to follow this caution may result in equipment damage.
Do not use caustic household drain cleaners in the condensate

pan or near the coil. Drain cleaners can quickly destroy a coil.

CAUTION

!

C. Disconnecting the Control Box Assembly

1. Disconnect power.

ELECTRICAL OPERATION HAZARD

Failure to follow this warning could result in personal injury

or death.
Before installation or servicing system, always turn off main

power to system. There may be more than one disconnect

switch. Turn off accessory heater power if applicable. Lock out

and tag switch with a suitable warning label.

!

WARNING

2. Remove control box cover (four screws).

A13385

Fig. 7 

 

Control Box Cover Removal

3. Remove control box assembly (five screws). If there is not

enough slack in field wiring (high and low voltage), it is

recommended to disconnect field wiring.

A13386

Fig. 8 

 

Control Box Removal

D. FPM(A,B)N, FMC4X, FMU4X 

 Disconnecting the Blower

Assembly

1. Disconnect power.

ELECTRICAL OPERATION HAZARD

Failure to follow this warning could result in personal injury

or death.
Before installation or servicing system, always turn off main

power to system. There may be more than one disconnect

switch. Turn off accessory heater power if applicable. Lock out

and tag switch with a suitable warning label.

!

WARNING

2. Remove control box cover (four screws). (See Fig. 7.)
3. Disconnect the (four) blower

motor power wires, noting

connection locations. (See Fig. 8.)

4. Loosen the conduit holding ties.

A13387

Fig. 9 

 

Conduit Holding Ties

5. Remove the four outer screws that attach the blower support

plate to each evaporator coil support.

Summary of Contents for FMC4X















Reviews: