background image

2

Please read these instructions carefully before use and retain for future reference.

Please operate according to this manual, otherwise the protection provided by the

device will be impaired or fail.

Do not point laser directly in your eyes or indirectly off reflective surfaces.

Check  the  condition  before  using.  If  you  find  any  cracking,  breakage,  damage  or

abnormality, or you consider the device broken, stop using the device immediately

Do not use the Thermometer if it operates abnormally. Protection may be impaired.
When in doubt, have the Thermometer serviced.

Do not operate the Thermometer around explosive gas, vapor, or dust.

To avoid a burn hazard, remember that highly reflective objects will often result in

lower than actual temterature measurements.

To avoid damaging the thermometer or the equipment under test protect them from

the following:

EMF (electro-magnetic fields) from arc welders, induction heaters, etc.

Static electricity.

Thermal shock (caused by large or abrupt ambient temperature changes – 

allow 30 minutes for the Thermometer to stabilize before use).

Do not leave the Thermometer on or near objects of high temperature.

Replace the batteries as soon as the low battery indicator appears on the display.

Remove dead batteries from the Thermometer or if it is not going to be used for a

long time.

Never mix old and new batteries together, or different types of batteries.

Never dispose of batteries in a fire, or attempt to recharge ordinary batteries.

Before replacing the battery, turn off the Thermometer and disconnect all the test

probes.

To prolong battery life turn off the Thermometer after use.

IMPORTANT SAFETY INFORMATION

WHAT’S INCLUDED

FEATURES

Infrared Thermometer with laser sighting.

9V 6F22 Alkaline Battery (included)

Instruction manual

Single-spot laser sighting.

Intelligent USB power input (does not charge internal battery).

Backlit display - Two level white/colour (when using USB power, this feature will be

on automatically).

Current temperature plus

MIN, MAX, DIF, AVG

temperature readings.

Easy emissivity selector.

Trigger lock.

Celsius and Fahrenheit

temperature measurement.

Tripod mount.

Summary of Contents for 72-820









Reviews: