background image

2

Please read these instructions carefully before use and retain for future reference.

• 

Please operate according to this manual, otherwise the protection provided by the 

device will be impaired or fail.

• 

Do not point laser directly in your eyes or indirectly off reflective surfaces.

• 

Check  the  condition  before  using.  If  you  find  any  cracking,  breakage,  damage  or 

abnormality, or you consider the device broken, stop using the device immediately

• 

Do not use the Thermometer if it operates abnormally. Protection may be impaired. 
When in doubt, have the Thermometer serviced.

• 

Do not operate the Thermometer around explosive gas, vapour, or dust.

• 

To avoid a burn hazard, remember that highly reflective objects will often result in 

lower than actual temperature measurements.

• 

To avoid damaging the thermometer or the equipment under test protect them from 

the following:

 

EMF (electro-magnetic fields) from arc welders, induction heaters, etc.

 

Static electricity.

 

Thermal shock (caused by large or abrupt ambient temperature changes –  

 

allow 30 minutes for the Thermometer to stabilize before use).

• 

Do not leave the Thermometer on or near objects of high temperature.

• 

Replace the batteries as soon as the low battery indicator appears on the display.

• 

Remove dead batteries from the Thermometer or if it is not going to be used for a 

long time.

• 

Never mix old and new batteries together, or different types of batteries.

• 

Never dispose of batteries in a fire, or attempt to recharge ordinary batteries.

• 

Before replacing the battery, turn off the Thermometer and disconnect all the test 

probes.

• 

To prolong battery life turn off the Thermometer after use.

IMPORTANT SAFETY INFORMATION

WHAT’S INCLUDED

FEATURES

• 

Infrared Thermometer with laser sighting.

• 

9V 6F22 Alkaline Battery (included)

• 

Instruction manual

• 

Single-spot laser sighting.

• 

White backlight.

• 

Synchronous display of the measured maximum and minimum value.

• 

Celsius and Fahrenheit temperature measurement.

• 

Dynamic battery capacity monitoring.

• 

Low voltage indication.

• 

Display screen.

• 

Adjustable emissivity.

• 

Alarm sounder for upper and lower limit.

Summary of Contents for 72-8732









Reviews: