5
CH1
OFF
3 2 . 0 0 V
3 2 . 0 0 V
0 6
. 0 0 V
3 . 0 0 0 A
3 . 0 0 0 A
S h i f t
AUTO
OCP
OFF
3 . 0 0 0 A
CH3
OFF
CH2
OFF
OCP
OFF
CH1
OFF
3 2 . 0 0 V
3 2 . 0 0 V
0 6
. 0 0 V
3 . 0 0 0 A
3 . 0 0 0 A
S h i f t
INDEP
OCP
OFF
3 . 0 0 0 A
CH3
OFF
CH2
OFF
OCP
OFF
OUT SET
INDEP OUT
PARA OUT
SERIES OUT
12
Programming
Output
Mode
Independent
Output
Mode
TECHNICAL SPECIFICATIONS
5.2 Sequence range activation
After setting all needed values and delays, move the cursor over the delay value
of the last step in the sequence to be used and press
[AUTO],
and a box
should appear after the value. After the automatic sequence reaches this step, it
will return to the first step and continuously repeat the sequence.
6. Automatic sequence execution
From the home screen, press
[AUTO]
, which will set the unit to AUTO mode.
Press
[OUTPUT]
to activate the selected and stored settings; the unit then will
output the sequences of t voltage, current, and delay parameters. The unit will
continued to run through the sequences. Press
[AUTO]
to stop the automatic
sequence.
7. Series and parallel operation mode
Press
[SHIFT][ PARA/SER]
to select between operation modes. Use the rotary
knob to select the desired output mode. Press
[ENTER]
to confirm and return to
the main screen. When the unit operates in series or parallel output modes,
channel 2 operates as the master (CH1 and CH2 will output the settings for Ch2).
In independent mode, each channel will output it’s own individual settings.
72-8795
≤
3mV
(
AC
±
5
%)
≤
3mA
10mV
Resolution
100
ppm+3mV
100
ppm+3mA
10%~90%≤ 100
ms
90
10
10
( 10
rated load)
%~
%
≤
≥
%
ms
Technical specifications
Specifications
Note: The following indexes are tested after unit being powered for 20 minutes.
Output
Voltage
Current
Load Effect
Voltage
Current
≤
3mV(
≤
8mV rated
>3.0A)
current
0~32V
2,
0-6V
x
0~3A
3
x
≤
3m (
≤
m rated current>3.0A)
A 5 A
Voltage
Current
Power Effect
Voltage
Current
≤
0.05
+10 mV(+20 mV rated voltage>36V)
%
≤
0.1
+5ma(+10 mA rated current>3.0A)
%
Voltage
Current
Voltage
Current
Set
Accuracy
(25 5
)
±
℃
Ripple
(20Hz-20MHz)
≤
3mArms(
≤
5mArms rated current>3.0A)
Voltage
Current
Temperature
Coefficient
(0
～
40
℃
)
Voltage
Current
10 mV
1mA(2mA rated current>3.0A)
1mA
（
2mA rated current>3A
）
Ripple
≤
1 mVrms
Read back
Resolution
Voltage rise
Current fall
Response Time
Voltage
Current
≤
10 mV
≤
10 mA
≤
10 mV
≤
10 mA
≤
0.1
+20 mV
%
20 mA
Series(Load)
Drift
Voltage
Current
Readback
Temperature
Coefficient
OPERATION
Serial
synchronous
operation
Serial
synchronous
error
