background image

ENGLISH

EN

BR2020/T (04–98)

5

MACHINE INSTALLATION

UNCRATING MACHINE

Carefully check carton for signs of damage.
Report damages at once to carrier.

To uncrate your machine, remove straps and
carefully lift or use a ramp to remove machine
from pallet.

ATTENTION:  To prevent dust skirt

damage, carefully TILT machine back when
removing from shipping crate.

CAUTION: Install batteries 

after removing

machine from pallet.

INSTALLING BATTERIES

WARNING:  Wear protective gloves and

shield eyes when handling batteries. Battery
acid can cause burns.

WARNING: Keep sparks and open flame

away. Batteries emit hydrogen gases,
explosion or fire can result.

Recommended Battery Specifications:

Three 12 volt deep cycle batteries. Consult  with
an Authorized Distributor for specific batteries.
Maximum battery dimensions are 78 mm W x 394
mm L x 362mm H.

FOR SAFETY: To prevent accidental

starting, be certain key is removed.

1.

Position machine on a level surface and set
parking brake.

Set Parking Brake

2.

Turn OFF all switches and remove key.

3.

Unlatch battery hood latches and open battery
compartment.  Remove loose battery cables.

Open Battery Compartment

4.

Carefully install batteries into battery tray and
arrange battery posts as shown. After
batteries are in place remove battery handles
to allow clearance for battery hood.

BATTERY TRAY

CHARGER PLUG

MACHINE 

FRONT

Battery Arrangement

WARNING: Do not drop batteries into

compartment! Battery and machine housing
damage may result. This damage is not
covered by Warranty.

5.

Connect cables to battery posts as shown.
(RED TO POSITIVE & BLACK TO
NEGATIVE)

 CONNECT LAST

CHARGER PLUG

MACHINE 

FRONT

BLK

BLK

RED

31

RED

Connect Battery Cables

6.

Double check cable connections and close
hood, fasten hood latches.

Summary of Contents for 604777













Reviews: