159
T600/T600e 9016605 (04-2018)
SERVICE
FOR SAFETY: Before leaving or servicing machine,
stop on level surface, turn off machine, remove
key, and set parking brake if equipped.
1. Completely drain the recovery tank and solution
tank.
2. Turn the key to the OFF position.
3. Disconnect the battery cable from the machine.
FOR SAFETY: When servicing machine, Disconnect
battery connection and charger cord before
working on machine.
4. Lift the recovery tank completely open.
NOTE: Do Not discard any items removed from the
solution tank. All removed items must be installed onto
the new solution tank.
5. Remove the batteries from the machine.
FOR SAFETY: When servicing machine, avoid
contact with battery acid, keep all metal objects off
batteries, and use a hoist or adequate assistance
when lifting batteries. Use a non-conductive
battery removal device.
6. Remove the rear squeegee assembly from the
machine.
7. Remove the recovery tank from the machine. See
REMOVING / REPLACING THE RECOVERY
TANK.
8. Remove the scrub head from the machine. See
applicable section for removing the scrub head
from the machine.
9. Remove the scrub head lift assembly from the
machine.
10. Remove optional ec-H2O, Severe Environment,
recovery tank rinse, and / or auto-fi ll assemblies
from the solution tank.
11. Remove the support bracket, right fi ll accessory
tray, left drain accessory tray, solution drain hose,
and tank cap / port fi ll strainer from the solution
tank.
12. Remove all electronic components, control
handle assembly, and controls from the machine.
Place circuit board / electronic components in
a safe place where they cannot be damaged.
See applicable sections for removing electronic
components and controls.
NOTE: To avoid damaging electronic components,
a static ground strap must be worn at all times while
handling circuit boards / control modules. Attach the
other end of the static ground strap to the machine
chassis.
13. Position a protective blanket or large section of
cardboard next to the side of the machine that will
be tipped onto the fl oor.
NOTE: Do Not allow the machine to drop when tipping
it onto the protective blanket. The scrub head and other
components could be damaged if machine is allowed
to drop. If necessary, remove the scrub head from the
machine before tipping the machine onto its side.
14. Carefully tip the machine onto the protective
blanket / cardboard.
15. Remove the transaxle assembly from the machine.
See REMOVE / INSTALL THE TRANSAXLE
ASSEMBLY.
16. Remove all fi ttings, hoses, and remaining
components from the bottom of the machine.
17. Remove the frame and all remaining parts and
components from the recovery tank.
18. Place the new solution tank onto the protective
blanket / cardboard.
19. Install removed parts and components onto
the new recovery tank in the reverse order of
disassembly.
20. Assemble components onto the recovery tank in
reverse order of disassembly.
Summary of Contents for T600e
