background image

BLEACH

• Do not use M.E.K.(methyl ethyl ketone) 

   to try and clean your inflatable, as this 

   will damage the vinyl 

• Do not use a chlorine based cleaner or 

   bleach, as this may damage the threads

• Do not use any cleaning products 

   containing alcohol to try and clean your 

   inflatable device, as this will damage any 

   printing that may be on your inflatable 

• Use water and/or mild cleaner sparingly 

   by sponging

• Excessive water or cleaner may penetrate 

   the seams and collect inside of the tubes 

   —also, bubbling from the seams during 

   operation may occur 

CLEANING THE INFLATABLE

Next, align unit

into a rectangle

shape—pancake

top and bottom

Front

Deflation Tubes

—Back of unit,

keep extended

888 322-5606 (toll free)

• 

Before deflating;

 Inspect for any damage 

   and repair as necessary 

• 

Clean 

inflatable amusement device(s) 

and 

   dry

, after use—by running air through it

• Unplug blower at the power source 

• Loosen first inflation/deflation tube 

   strap and remove tube from blower cone 

   —make sure tube is pulled away from 

   the inflatable and is straight 

• Loosen second inflation/deflation tube 

   strap and pull tube away from inflatable 

• Open all deflation flaps

• While the inflatable amusement device 

   is deflating, remove stakes, put blower 

   fan away, and store extension cord(s) 

• Two people, minimum, needed to fold

• Guide inflatable inward and to the front

   —while the air is being released

• Begin folding inflatable amusement 

   device—pull vertical peaks/shapes toward 

   the front, to flatten and release more air

• Next, situate top of unit over the bottom,

   pancake style—and fold peaks into the 

   middle, see (

drawing

)

• Once you make the folds, you will notice 

   that air is still inside the game—start at 

   the front and walk, in stocking feet, to 

   the back—removing most of the air 

• Work the air out towards the back of 

   the unit through the inflation tube(s)

• Commercial inflatables take 5–15 

   minutes to completely deflate 

DEFLATION AND FOLDING- cont.

DEFLATION AND FOLDING

5

Before deflation, remove all accessories that may be

applicable to your unit—also be sure to use a quality 

broom and sweep the surface of the game free of 

any debris

Check to make sure that no sharp 

objects have fallen into the seams 

of the game, Eg. pens, pencils, etc.

—items such as these can cause 

damage to the inflatable during 

the rolling up process

Summary of Contents for GA Bounce Kaleidoscope Castle 7013












Reviews: