background image

www.TERAFLEX.com

18

Revision B

999376

PRODUCT INFORMATION

MAINTENANCE INFORMATION:

It is the buyer’s responsibility to have all suspension, drivetrain, steering, and other components checked for proper tightness and torque after the first 

100 miles and every 3000 miles after that.

NOTICE TO INSTALLER: 

The enclosed “Warning to Driver” sticker must be installed in the vehicle in driver’s view. This sticker is to act as a constant safety reminder when oper-

ating the vehicle. It is your responsibility as the equipment installer to install the provided sticker and to forward the product instructions to the vehicle’s 

owner for review. If a “Warning to Driver” sticker or product installation guide were not included in the kit, FREE replacement stickers and instructions 

are available by request. It is the installer’s duty to ensure a safe and controllable vehicle after the modifications have been performed.

WARNING: 

Neither the seller nor the manufacturer will be liable for any loss, damage, or injury directly or indirectly arising from the use of or inability to determine 

the use of these products. Before using, the user shall determine the suitability of the products for its intended use, and the user shall assume all re-

sponsibility and risk in connection therewith.

WARNING TO DRIVER:

 

This vehicle has been modified to enhance off road performance and has unique handling characteristics. Use in harsh environments can cause ex

-

treme stress on the components. Vehicle should be inspected after being off road to make sure that all the components are in working order and safe to 

travel on the highway. All fasteners should be checked so that they are at the correct torque specifications as the vibration and stresses from off roading 

may cause critical fasteners to work loose. Extra care should be taken to inspect the critical components, steering, and brake systems. During each oil 

change components such as arms, tie rod ends, etc should be greased and checked for excessive wear. Any worn components should be replaced. 

When returning to the pavement always set or restore tire air pressure to the factory recommendation and connect or engage any disabled sway bar 

mechanisms. Because of the higher center of gravity and larger tires, this vehicle handles and reacts differently than many passenger cars, both on and 

off road. You must drive it safely! Extreme care should be taken to prevent vehicle rollover or loss of control, which can result in serious injury or death. 

Avoid sudden sharp turns or abrupt maneuvers. Generally, braking performance and capabilities are decreased when significantly larger/heavier tires 

are used, especially when used in combination with transfer case low-range reduction kits. Take this into consideration while driving. Do not add, alter 

or fabricate any factory or aftermarket parts to increase vehicle height over the intended height of the TeraFlex product purchased. Mixing component 

brand is not recommended. TeraFlex Inc. will not be responsible for any altered product or any improper installation or use of our products. We will 

be happy to answer any questions concerning the design, function, and correct use of our products. It is ultimately the buyer’s responsibility to have 

all bolts/nuts checked for tightness after the first 100 miles and then every 3000 miles. Wheel alignment, steering system, suspension and drive line 

systems must be inspected by a qualified professional mechanic at least every 3000 miles.

TERAFLEX PRODUCT WARRANTY: 

TeraFlex Inc. warrants TeraFlex Suspension products to the original retail purchaser to be free of defects in material and workmanship for as long as 

the original purchaser owns the vehicle on which products were originally installed. 

Failure to complete regular maintenance (grease every 3000 miles) on TeraFlex FlexArms will void this warranty. All other conditions of the standard 

TeraFlex product warranty apply. 

All TeraLow products are covered by the TeraFlex two (2) year warranty to be free of defects in material and workmanship for two years from date 

purchased. 

TeraFlex axles are covered by a 12-month warranty to be free of defects in materials and workmanship. 

This warranty does not cover or include product finish, improperly installed or applied products, improperly maintained products, products or compo

-

nents used for racing or competition or damage due to abuse or neglect, products that fail due to the use of larger tire and wheel combinations. 

All returns must be accompanied by an original invoice. It is the customer’s responsibility to remove the product from the vehicle. Shipping charges are 

the responsibility of the customer. TeraFlex Inc. will pay the return freight if the product meets the terms of warranty. 

This warranty is for the replacement or repair of defective TeraFlex products only and does not include freight charges, labor charges for removal of 

or installation of TeraFlex or related products or components, costs incurred due to down time of the vehicle, or lost profits due to vehicle down time. 

A returned goods authorization number (RGA#) must accompany any returned products. For more information please contact a TeraFlex customer 

service representative.

COPYRIGHT

©Copyright  2014. All  rights  reserved,  TeraFlex  Inc.    Reproduction  of  this  catalog  and/or  any  of  its  contents  without  written  permission  is  strictly             

prohibited.

TeraFlex® is a registered trademark of TeraFlex Inc.  All trade names and logos including but not limited to TeraFlex, FlexArms, RockGuard, Monster, 

and LCG are protected by law and duplication of trade names and/or logos are strictly prohibited.

TeraFlex Inc. reserves the right to update, discontinue, redesign, modify finish, part number or component build parts if deemed necessary without 

written notice. TeraFlex Inc., and any associated dealers are not responsible for misprints or typographical errors that may have inadvertently  been 

made within this instruction sheet.

Jeep®  and the Jeep® grill are registered trademarks of Fiat Chrysler Automobiles N.V., and have no affiliation 

with TeraFlex Inc.

                        , Inc.

5680 West Dannon Way

West Jordan, UT. 84081

Phone/801.713.3314

Fax/801.713.2313

www.teraflex.com

Summary of Contents for 1365000



















Reviews: