34
INV DC status codes
400
DC bus voltage high
401
Inverter controller board power supply 1 out of tolerant
402
Inverter controller board power supply 2 out of tolerant
404
Inverter stop because (+)DC bus voltage is low
405
Inverter stop because (-)DC bus voltage is low
406
Inverter within time window 4 times DC bus voltage is high
INV General status codes tablosu
500
Inverter received remote power off signal from RS232
501
Inverter received remote power off signal from CAN interface
502
Inverter sensed IGBT fault alarm 4 times within time window (30 minutes)
503
Inverter sensed Overtemperature alarm 4 times within time window (30 minutes)
504
Inverter sensed 3 phase AC O/P voltage low alarm 4 times within time window (30 minutes)
505
Inverter sensed 3 phase AC O/P voltage high alarm 4 times within time window (30 minutes)
506
Inverter Timeout error during eprom read or write
507
Inverter Memory checksum error
508
Inverter 3 output phases overloaded output shutdown
509
Inverter maintenance by-pass switch closed
510
Inverter IGBT fault error
511
Inverter overtemperature shutdown
512
Inverter 3 phase AC output voltage low
513
Inverter 3 phase AC output voltage high
514
Inverter output CB energized but still it looks like not energized
515
Inverter output CB not energized but stil it looks like energized
516
Inverter fault occured for restart password required
517
Inverter output CB energized but at the UPS output there is no 3 phase AC voltage
518
Inverter By-pass voltage is OK but at the UPS output there is no 3 phase AC voltage
INV Control activity status codes
612
INV Over RS232 interface battery quantity updated
613
INV Over CAN1 interface battery quantity updated
614
INV Over RS232 interface by-pass and output frequency updated
615
INV Over CAN1 interface by-pass and output frequency updated
616
INV Over RS232 interface By-pass and output voltage updated
617
INV Over CAN1 interface By-pass and output voltage updated
618
INV Over RS232 interface factory options updated
619
INV Over CAN1 interface factory options updated
620
INV Over RS232 interface user options updated
621
INV Over CAN1 interface user options updated
622
INV Over RS232 interface general test command received
623
INV Over CAN1 interface general test command received
624
INV Over RS232 interface transfer load to by-pass command received
625
INV Over CAN1 interface transfer load to by-pass command received
626
INV Over RS232 interface transfer load to UPS command received
627
INV Over CAN1 interface transfer load to UPS command received
628
INV Over RS232 interface Copy operating RAM to Factory settings zone command received
629
INV Over CAN1 interface Copy operating RAM to Factory settings zone command received
630
INV Over RS232 interface Copy factory settings to operating RAM command received
631
INV Over CAN1 interface Copy factory settings to operating RAM command received
632
INV Over RS232 interface Copy operating RAM to User settings zone command received
633
INV Over CAN1 interface Copy operating RAM to User settings zone command received
634
INV Over RS232 interface regenerative back feed activated
635
INV Over CAN1 interface regenerative back feed activated
Summary of Contents for DS300SHB Series
