10
INV CODE = 0XXX
Status code of inverter module at that moment.
A00 INV ERROR = XXXX
Error
System error in inverter module XXXX value indicates the occurring error, service code is required to
start the device
-call the service
A01 OVER CURRENT
Alarm
Over loading occurred in the inverter module
A02 OVER HEAT BREAK
Alarm
Over heat occurred in the inverter module
A03 ACCUMULATOR HIGH
Alarm
Accumulator voltage found high
A04 LOW OUTPUT
Alarm
UPS Output voltage found low
A05 OUTPUTN HIGH
Alarm
UPS Output voltage found high
A02 OVER LOAD BREAK
Alarm
Over loading occurred at device output stop the device
A07 SHORT CIRCUIT
Alarm
Short circuit occurred at UPS output device blocked
A08 IN MAINTENANCE
Alarm
Device maintenance switch is on
A09 MANUAL BYPASS
Alarm
Device taken to manual by-pass position from the front panel
A10 ACCUMULATOR LOW BREAK
Alarm
Accumulator voltage found low
A11 EMERGENCY SHUT-OFF
Alarm
External emergency shut-off signal detected
A12 DC BALANCE
Alarm
DC available at INV output before inverter starts
A13 PEAK HIGH
Alarm
Short period over load drawn from UPS output
A14 INV FAILED TO START
Alarm
Inverter module failed to create voltage at output during start
A17 BYPASS INTERRUPTED
Warning
By-pass input voltage interrupted
A18 BYPASS VOLT
Warning
By-pass input voltage out of tolerance
A19 BYPASS FREQUENCY
Warning
By-pass voltage frequency is out-of-tolerance
A20 OVER LOAD
Warning
Over loading available at device output device will stop
A21 OVER HEAT
Warning
Over heating available at device output device will stop
A22 OUTPUT INTERRUPTED
Warning
No voltage at UPS output
A23 BYPASS
Warning
Device transferred the load to by-pass input
A24 REVERSE CURRENT
Warning
Regenerative load applied voltage to device output
A25 INV RESET
Warning
Inverter module supply applied recently (only seen when the device is started for the first time)
A26 ACCUMULATOR LOW
Warning
Accumulator low warning, device will stop soon and electricity of connected loads will be interrupted.
A27 GENERATOR MODE
Warning
Device operates at generator position
A28 PHASE LOSS
Warning
Interruption in any of phases at UPS output
A29 NO SYNCHRON
Warning
Inverter is not synchronous to by-pass input
A30 SHORT CIRCUIT
Warning
Short circuit occurred and passed at UPS output
A31 OUTPUT SWITCH
Warning
Device output switch is closed
A32 SERVICE LOGIN
Warning
Device logged in with service authorizations
A34 BYP.PHASE ROTATE
Warning
Order of 3 phases applied to device by-pass input is reverse
A35 INV STOP
Warning
Inverter module stopped for any reason
L03 TH1 LOW HEAT
Warning
TH1 heat sensor heat is lower than the adjusted alarm level
L04 TH2 LOW HEAT
Warning
TH2 heat sensor heat is lower than the adjusted alarm level
L05 FAN MAINTENANCE
Warning
FAN maintenance period expired warning
L06 ACCUMULATOR
MAINTENANCE
Warning
ACCUMULATOR maintenance period expired warning
L07 OPT MAINTENANCE
Warning
Allocated for future
L08 TH1 SENSOR ERROR
Warning
TH1 temperature sensor broken or short circuit
L09 TH2 SENSOR ERROR
Warning
TH2 temperature sensor broken or short circuit
L10 ERROR RESET
Warning
Not recorded in logs
L11 ACCUMULATOR OUT-OF-
SERVICE
Warning
External accumulator switch is off
L12 GENERAL MAINTENANCE
Warning
General maintenance period expired warning
L13 PFC CAN COMM ERR
Warning
PFC module CAN communication broken warning
L14 INV CAN COMM ERR
Warning
INV module CAN communication broken warning
L17 SLEEP WAIT
Warning
Wait warning before the sleep mode
L18 WAKE-UP WAIT
Warning
Wait warning before transition from sleep to wake-up mode
A36 INV DC LOW
Warning
DC Busbar voltage is below 120 volt DC value
A37 AC CURRENT LIMIT
Warning
UPS output current is over RXXXX value
A38 FUSE BLOWN
Warning
Any fuse blown in the device
A39 SUPPLY TOL.
Alarm
Inverter card supply values out-of-tolerance
A41 SLEEP MODE
Warning
Inverter module in sleep mode
A43 USER LOGIN
Warning
Device logged in with user authorizations
A45 ENTER PASSWORD
Error
Error occurred at device inverter module service code required
-call the service
Summary of Contents for RM2020
Page 1: ...0 UPS REMOTE MONITORING PANEL RMP X1 INSTALLATION AND USER S GUIDE ...
Page 14: ...13 ...
Page 15: ...14 AGKK13150 08 2018 ...
