background image

GVT-427B User Manual

2

FOR UNITED KINGDOM ONLY

NOTE: This lead/appliance must only be wired by

competent persons

WARNING: THIS APPLIANCE MUST BE EARTHED

IMPORTANT: The wires in this lead are coloured in

accordance with the following code:

Green/ Yellow: Earth

Blue:                 Neutral

Brown:              Live (Phase)

As the colours of the wires in main leads may not correspond

with  the  colours  marking  identified  in

 

your  plug/appliance,

proceed as follows:
The wire which is coloured Green & Yellow must be connected

to the Earth terminal marked with the letter E or by the earth
symbol 

 or coloured Green or Green & Yellow.

The  wire  which  is  coloured  Blue  must  be  connected  to  the

terminal which is marked with the letter N or coloured Blue or

Black.
The wire which is coloured Brown must be connected to the

terminal marked with the letter L or P or

 coloured

 Brown or

Red.
If in doubt, consult the instructions provided with the equipment

or contact the supplier.

This cable/appliance should be protected by a suitably rated

and approved HBC mains fuse : refer

 

to the rating information

on  the  equipment  and/or  user  instructions  for  details.  As  a

guide, cable

GVT-427B User Manual

3

of 0.75mm

²

 should be protected by a 3A or 5A fuse. Larger

conductors  would  normally  require  13A  types,  depending  on

the connection method used.
Any moulded mains connector that requires removal /replace-

ment must be destroyed by removal of any  fuse & fuse carrier

and  disposed  of  immediately,  as  a  plug  with  bared  wires  is

hazardous if a engaged in live socket. Any re-wiring must be

carried out in accordance with the information detailed on this

label.

Summary of Contents for GVT-427B










Reviews: