background image

 

Chapter 1 – Safety 

 

 

TestEquity 123C Temperature Chamber 

Page 1-1

 

Chapter 1 – Safety Instructions 

 

Introduction 

 

 

Follow all CAUTION notices to prevent damage to the chamber or your test sample. Failure to 

follow all CAUTION notices may void your warranty. CAUTION may also indicate a 

potentially hazardous situation which, if not avoided, may result in minor or moderate personal 

injury. 

 

WARNING indicates a potentially hazardous situation which, if not avoided, could result in 

death or serious injury. 

 

The safety alert symbol 

!

 precedes a general CAUTION or WARNING statement. 

 

The electrical hazard symbol 

2

 precedes an electric shock hazard CAUTION or WARNING 

statement. 

 

Installation Safety Notices 

 

 

2

 

WARNING:

  The power cord is equipped with a NEMA 5-20P grounded/polarized plug. To 

prevent a shock hazard, DO NOT defeat the ground or polarization feature. 

This device MUST be plugged DIRECTLY into a properly grounded and 

polarized NEMA 5-20R receptacle. Due to high current demand on start-up, 

use of an extension cord is NOT recommended.

 

 

!

 

CAUTION:

  The minimum clearance you should allow for proper ventilation around the 

chamber must be at least 6" from both the left and right side, and 12" from the 

rear.

 

 

!

 

CAUTION:

  This chamber is designed for operation in a conditioned laboratory 

environment. Operation above 30°C (85°F) or below 16°C (60°F) ambient 

room temperature is NOT recommended. 

 

Summary of Contents for 123C














































Reviews:

Related manuals for 123C