background image

ZEUS 3.0 (MADE IN EUROPE) 

~ 5 ~ 

TESUP 

 

 

 

 

 

 

 

 

Before you begin installing, read 

this entire owner’s manual. Identify and note your model 

wind  turbine  where  it  appears  in  this  manual.  Following  the  instruction  and 
recommendations  in  this  manual  will  help  assure  safe  and  enjoyable  use  of  your  new 
renewable energy system. 

 

Please take the time to read through this manual prior to assembly. 

o

 

Place this instruction manual in a safe place for reference.  

o

 

Wait  until  a  calm  day  to  install  or  perform  maintenance  on  your  Turbine  with 
activation of brake. 

o

 

Listen  to  your  Turbine,  if  you  hear  any  mechanical  noise,  maintenance  may  be 
required, please contact your Turbine dealer. 

o

 

After installation re-adjust and tighten the screws and bolts. 

o

 

Adhere to proper grounding techniques as established by the National Electrical 
Code. 

o

 

Your Wind Turbine must be installed in accordance with this manual and local and 
national building code. Incorrect installation may void your warranty. 

o

 

Wind Turbine blades spin at a potentially dangerous speed, this must be respected. 
Never approach a Turbine in motion.  

o

 

Note  wire  size  prior  to  wiring.  Any  under  sizing  of  wire  can  be  potentially 
dangerous. 

o

 

Check the manual brake periodically. 

o

 

Check  the  battery  health  periodically.  The  low  battery  voltage  and  improper 
connection can cause over-spin issues. 

2.1.1 Operating and Installing Conditions: 
 

 

Please make sure that: 

o

 

The wind turbine system has been erected correctly by a suitably trained 
person. 

o

 

All operating personnel have read and fully understood this translation of the 
original instructions 

o

 

The wind turbine system is properly maintained and repaired. 

 

 

2.

 

GENERAL 

2.1 GENERAL INSTRUCTIONS: 

 

 

Summary of Contents for ZEUS3.0


































Reviews:

Related manuals for ZEUS3.0