Texas Instruments ADC08060 User Manual Download

Page: 1 / 16

SLAU715 – February 2017

ADC08060 Evaluation Module

User's Guide

SLAU715 – February 2017

ADC08060 Evaluation Module

This user's guide describes the function and use of the ADC08060 evaluation module (EVM). Included in
this document are a quick-start guide, instructions for optimizing evaluation results, jumper and connector
descriptions, software description, and alternate hardware configurations.

Contents

Overview

......................................................................................................................

1.1

Required Hardware

.................................................................................................

1.2

Required Software

..................................................................................................

1.3

Evaluation Board Feature Identification Summary

.............................................................

1.4

References

..........................................................................................................

Quick-Start Guide

............................................................................................................

2.1

Software Installation

................................................................................................

2.2

Hardware Setup Procedure

.......................................................................................

2.3

Software Setup Procedure

.........................................................................................

2.4

Quick-Start Troubleshooting

.......................................................................................

Optimizing Evaluation Results

.............................................................................................

3.1

Clocking Optimization

..............................................................................................

3.2

Coherent Input Source

.............................................................................................

3.3

HSDC Pro Settings

.................................................................................................

Alternate Hardware Configurations

......................................................................................

4.1

Clocking Options

..................................................................................................

4.2

Voltage Reference Options

......................................................................................

Appendix A

Jumper and Connector Descriptions

............................................................................

List of Figures

EVM Feature Locations

.....................................................................................................

Quick-Start Test Setup

......................................................................................................

HSDC Pro GUI Main Panel

.................................................................................................

Data Capture Results From Quick-Start Procedure

.....................................................................

List of Tables

Quick-Start Performance Measurements

.................................................................................

Troubleshooting Tips

........................................................................................................

HSDC Pro Settings to Optimize Results

..................................................................................

Jumper Descriptions and Default Settings

..............................................................................

Connector Descriptions

....................................................................................................

Trademarks

Microsoft, Windows are registered trademarks of Microsoft Corporation.
All other trademarks are the property of their respective owners.

Summary of Contents for ADC08060

















Search results

Summary of Contents for ADC08060

Reviews:

Related manuals for ADC08060

Brands by name

Popular brands

Texas Instruments ADC08060, User Manual

Search results

Summary of Contents for ADC08060

Reviews:

Related manuals for ADC08060

Brands by name

Popular brands