Texas Instruments ADC3221EVM User Manual Download

Page: 10 / 36

Introduction

www.ti.com

SLAU579D – June 2014 – Revised August 2018

Submit Documentation Feedback

ADC3xxxEVM and ADC3xJxxEVM

Table 3. ADC3xxxx EVM Connectors

Device

Connector

Description

ADC32xx

AINP – positive input for A, Ch1 single ended input

AINM – negative input for A, DNI

BINM – negative input for B, DNI

BINP – positive input for B, Ch2 single ended input

CLK_INP – positive CLK input, single ended clock input

J10

CLK_INM – negative CLK input, DNI

J11

SYSREF_INP – positive input for SYSREF frame clock, single ended input

J12

SYSREF_INM – negative SYSREF input, DNI

J13A, B

HSMC data connector to TSW1400 evaluation platform

J14

Mini USB connector for SPI control

J15

Power connector for 5-V adapter

ADC34xx

AINP – positive input for A, Ch1 single ended input

AINM – negative input for A, DNI

BINM – negative input for B, DNI

BINP – positive input for B, Ch2 single ended input

CINP – positive input for C, Ch3 single ended input

CINM – negative input for C, DNI

DINM – negative input for D, DNI

DINP – positive input for D, Ch4 single ended input

CLK_INP – positive CLK input, single ended clock input

J10

CLK_INM – negative CLK input, DNI

J11

SYSREF_INP – positive input for SYSREF frame clock, single ended input

J12

SYSREF_INM – negative SYSREF input, DNI

J13A, B

HSMC data connector to TSW1400 evaluation platform

J14

Mini USB connector for SPI control

J15

Power connector for 5-V adapter

ADC32J/34Jxx

AIN_CH-AP – positive input for CHA, single ended input (DNI for ADC32Jxx)

AIN_CH-AM – negative input, (DNI for ADC32Jxx and ADC34Jxx)

BIN_CH-BP – positive input for CHB (CHA input for ADC32Jxx), single ended input

BIN_CH-BM – negative input for CHB (CHA input for ADC32Jxx and ADC34Jxx)

CIN_CH-CP – positive input for CHC (CHB input for ADC32Jxx), single ended input

CIN_CH-CM – negative input for CHC (CHB input for ADC32Jxx and ADC34Jxx)

DIN_CH-DP – positive input for CHD, single ended input (DNI for ADC32Jxx)

DIN_CH-DM – negative input, (DNI for ADC32Jxx and ADC34Jxx)

EXT_ADC_CLK – external ADC clock connection for ADC, if needed

J23

EXT - external SYSREF connection for ADC, if needed (positive input)

J24

EXT SYSREF– - external SYSREF connection for ADC, if needed (negative input)

J10

LMK_CLKIN – external input clock for LMK use, if needed (for clock distribution mode)

J13

DCLKOUT6P – LMK output test point, positive

J14

DCLKOUT6N – LMK output test point, negative

J15

DCLKOUT7P – LMK output test point, positive

J16

DCLKOUT7N – LMK output test point, positive

J20

5-V input power jack

J18

Mini USB connector for SPI GUI control

J19

CPLD JTAG port

Summary of Contents for ADC3221EVM





































Search results

Summary of Contents for ADC3221EVM

Reviews:

Related manuals for ADC3221EVM

Brands by name

Popular brands

Texas Instruments ADC3221EVM, User Manual

Search results

Summary of Contents for ADC3221EVM

Reviews:

Related manuals for ADC3221EVM

Brands by name

Popular brands