Schematics, PCB Layers, and Bill of Materials
STANDARD TERMS AND CONDITIONS FOR EVALUATION MODULES
1.
Delivery:
TI delivers TI evaluation boards, kits, or modules, including any accompanying demonstration software, components,
or documentation (collectively, an “EVM” or “EVMs”) to the User (“User”) in accordance with the terms and conditions set forth
herein. Acceptance of the EVM is expressly subject to the following terms and conditions.
1.1 EVMs are intended solely for product or software developers for use in a research and development setting to facilitate
feasibility evaluation, experimentation, or scientific analysis of TI semiconductors products. EVMs have no direct function
and are not finished products. EVMs shall not be directly or indirectly assembled as a part or subassembly in any
finished product. For clarification, any software or software tools provided with the EVM (“Software”) shall not be subject
to the terms and conditions set forth herein but rather shall be subject to the applicable terms and conditions that
accompany such Software
1.2 EVMs are not intended for consumer or household use. EVMs may not be sold, sublicensed, leased, rented, loaned,
assigned, or otherwise distributed for commercial purposes by Users, in whole or in part, or used in any finished product
or production system.
2
Limited Warranty and Related Remedies/Disclaimers
:
2.1 These terms and conditions do not apply to Software. The warranty, if any, for Software is covered in the applicable
Software License Agreement.
2.2 TI warrants that the TI EVM will conform to TI's published specifications for ninety (90) days after the date TI delivers
such EVM to User. Notwithstanding the foregoing, TI shall not be liable for any defects that are caused by neglect,
misuse or mistreatment by an entity other than TI, including improper installation or testing, or for any EVMs that have
been altered or modified in any way by an entity other than TI. Moreover, TI shall not be liable for any defects that result
from User's design, specifications or instructions for such EVMs. Testing and other quality control techniques are used to
the extent TI deems necessary or as mandated by government requirements. TI does not test all parameters of each
EVM.
2.3 If any EVM fails to conform to the warranty set forth above, TI's sole liability shall be at its option to repair or replace
such EVM, or credit User's account for such EVM. TI's liability under this warranty shall be limited to EVMs that are
returned during the warranty period to the address designated by TI and that are determined by TI not to conform to
such warranty. If TI elects to repair or replace such EVM, TI shall have a reasonable time to repair such EVM or provide
replacements. Repaired EVMs shall be warranted for the remainder of the original warranty period. Replaced EVMs shall
be warranted for a new full ninety (90) day warranty period.
3
Regulatory Notices:
3.1
United States
3.1.1
Notice applicable to EVMs not FCC-Approved:
This kit is designed to allow product developers to evaluate electronic components, circuitry, or software associated with
the kit to determine whether to incorporate such items in a finished product and software developers to write software
applications for use with the end product. This kit is not a finished product and when assembled may not be resold or
otherwise marketed unless all required FCC equipment authorizations are first obtained. Operation is subject to the
condition that this product not cause harmful interference to licensed radio stations and that this product accept harmful
interference. Unless the assembled kit is designed to operate under part 15, part 18 or part 95 of this chapter, the
operator of the kit must operate under the authority of an FCC license holder or must secure an experimental
authorization under part 5 of this chapter.
3.1.2
For EVMs annotated as FCC – FEDERAL COMMUNICATIONS COMMISSION Part 15 Compliant:
CAUTION
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device
may not cause harmful interference, and (2) this device must accept any interference received, including interference
that may cause undesired operation.
Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority
to operate the equipment.
FCC Interference Statement for Class A EVM devices
NOTE: This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part
15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the
equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency
energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio
communications. Operation of this equipment in a residential area is likely to cause harmful interference in which case
the user will be required to correct the interference at his own expense.
SPACER
SPACER
SPACER
SPACER
SPACER
SPACER
SPACER
30
DRV2605EVM-BT User's Guide
SLOU391 – May 2014
Copyright © 2014, Texas Instruments Incorporated
