MSP430xG461x
MIXED SIGNAL MICROCONTROLLER
SLAS508I − APRIL 2006 − REVISED MARCH 2011
30
POST OFFICE BOX 655303
•
DALLAS, TEXAS 75265
absolute maximum ratings over operating free-air temperature (unless otherwise noted)
†
Voltage range applied at V
CC
to V
SS
−0.3 V to 4.1 V
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Voltage range applied to any pin (see Note)
−0.3 V to V
CC
+ 0.3 V
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Diode current at any device terminal .
±
2 mA
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Storage temperature range, T
stg
:
Unprogrammed device
−55
°
C to 150
°
C
. . . . . . . . . . . . . . . . . . . . . . . . . . . .
Programmed device
−40
°
C to 85
°
C
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
†
Stresses beyond those listed under “absolute maximum ratings” may cause permanent damage to the device. These are stress ratings only, and
functional operation of the device at these or any other conditions beyond those indicated under “recommended operating conditions” is not
implied. Exposure to absolute-maximum-rated conditions for extended periods may affect device reliability.
NOTE: All voltages referenced to V
SS.
The JTAG fuse-blow voltage, V
FB
, is allowed to exceed the absolute maximum rating. The voltage is applied
to the TDI/TCLK pin when blowing the JTAG fuse.
recommended operating conditions
MIN
NOM
MAX
UNITS
Supply voltage during program execution (see Note 1),
V
CC
(AV
CC
= DV
CC1/2
= V
CC
)
MSP430xG461x
1.8
3.6
V
Supply voltage during flash memory programming (see Note 1),
V
CC
(AV
CC
= DV
CC1/2
= V
CC
)
MSP430FG461x
2.7
3.6
V
Supply voltage during program execution,
SVS enabled and PORON = 1 (see Note 1 and Note 2),
V
CC
(AV
CC
= DV
CC1/2
= V
CC
)
MSP430xG461x
2
3.6
V
Supply voltage (see Note 1), V
SS
(AV
SS
= DV
SS1/2
= V
SS
)
0
0
V
Operating free-air temperature range, T
A
MSP430xG461x
−40
85
°
C
LFXT1
t l f
f
LF selected, XTS_FLL = 0
Watch crystal
32.768
LFXT1 crystal frequency, f
(LFXT1)
(see Note 2)
XT1 selected, XTS_FLL = 1
Ceramic resonator
450
8000
kHz
(see Note 2)
XT1 selected, XTS_FLL = 1
Crystal
1000
8000
kHz
XT2 crystal frequency f
Ceramic resonator
450
8000
kHz
XT2 crystal frequency, f
(XT2)
Crystal
1000
8000
kHz
V
CC
= 1.8 V
DC
3.0
Processor frequency (signal MCLK), f
(System)
V
CC
= 2.0 V
DC
4.6
MHz
Processor frequency (signal MCLK), f
(System)
V
CC
= 3.6 V
DC
8.0
MHz
NOTES:
1. It is recommended to power AV
CC
and DV
CC
from the same source. A maximum difference of 0.3 V between AV
CC
and DV
CC
can
be tolerated during power up and operation.
2. The minimum operating supply voltage is defined according to the trip point where POR is going active by decreasing the supply
voltage. POR is going inactive when the supply voltage is raised above the minimum supply voltage plus the hysteresis of the SVS
circuitry.
3. In LF mode, the LFXT1 oscillator requires a watch crystal. In XT1 mode, LFXT1 accepts a ceramic resonator or a crystal.
ÇÇÇÇÇ
ÇÇÇÇÇ
ÇÇÇÇÇ
ÇÇÇÇÇ
ÇÇÇÇÇ
ÇÇÇÇÇ
1.8
3.6
2.7
3
3.0 MHz
8.0 MHz
Supply Voltage − V
Supply voltage range, MSP430FG461x,
during flash memory programming
Supply voltage range,
MSP430xG461x, during
program execution
2.0
4.6 MHz
f
System
(MHz)
Figure 1. Frequency vs Supply Voltage, Typical Characteristic
Summary of Contents for MSP430CG4616IPZ
Page 110: ......
