Texas Lilli 534B, Instruction Manual

11 

Never attempt to make any adjustments, while the 
engine is running. 

Use extreme caution when reversing or pulling the 
machine backwards 

Never operate the engine indoor or in areas with low 
ventilation. The exhaustion from the engine contains 
carbon monoxide. Failure to observe could result in 
permanent injury or death. 

Gasoline safety 

Use extreme care in handling gasoline. Gasoline is 
extremely flammable and the fumes are explosive. 

Serious personal injury can occur, when gasoline is 
spilled on yourself or your clothes. Rinse your skin and 
change clothes immediately! 

Use only an approved gasoline container. Do not use 
soft drink bottle or similar! 

Extinguish all cigarettes, cigars, pipes and other sources 
of ignition. 

Never refuel your machine indoors. 

Let the engine cool down before refilling 

Never fill the fuel tank to more than 2.5 cm below bottom 
of filler in order to provide space for fuel to expansion. 

After refueling, ensure that the cap tighten securely. 

Never use the lock-function on the gasoline gun, when 
refueling. 

Do not smoke while refueling. 

Never refuel inside a building or where gasoline fumes 
may get in contact with an ignition source.  

Keep gasoline and engine away from appliance, pilot 
lights, barbecues, electric appliances, power tools, etc. 

If the fuel tank has to be drained, this shall be done 
outdoors  

Maintenance and storage 

The engine shall be stopped when carrying out 
maintenance and cleaning operations, when changing 
tools and when being transported by means other than 
under its own power. 

Check regularly that all bolts and nuts are tightened. 
Retighten if necessary. 

The engine must be completely cooled before storing 
indoors or covered. 

If the machine unused for a period of time, please refer 
to the instructions in this manual.  

Maintain or replace safety and instruction labels, as 
necessary. 

Only use original spare parts or accessories. If not 
original parts or accessories is used, the liability is no 
longer applied.   

Replace faulty silencers. 

Miscellaneous 

The gears are delivered pre-greased. However, always 
ensure they are well greased before each use. 

The motor is not pre-filled with oil. 

Factory-fitted control devices, such as the handle-
mounted clutch cable, must not be removed or exposed. 

Only drain the fuel tank outdoors. Gasoline is extremely 
flammable and the fumes are explosive. 

Ensure that the machine is properly secured when 
transported on a flatbed etc. 

Reduce the throttle during engine shutdown and close 
the fuel valve. 

Due to vibrations, it is recommended to take a break for 
every 30 minuttes use to avoid fatique in your arms. 
 

Assembly 

 
Please follow the steps in figure: 

(Actual model may vary from the illustration shown) 
 

1. 

Box content 

A. Extension 

blades 

B.  Tiller with cables and support wheels 
C. Blades 

Outer 

D. Side 

guards 

E.  Handlebar (Lilli 572/575) 
F. Depth 

skid 

G.  Mounting bracket for handlebar (Lilli 572/575) 
H.  Lower handle x2 (Lilli 534/535) 
I. 

Handlebar (Lilli 534/535) 
 

2. 

Only for model Lilli 534/535: 
Fit the lower handle section. Use the supplied mountings 
and bolts.  
 
Fit the handle. Use the supplied assembly kit as shown. 

3. 

Only for model Lilli 572/575: 
Fit the handle into the bracket (1-G) fasten with hand 
wheel. 
 
NB: Ensure the bolt goes through the spring.  
 

4. 

Mount clutch handle and throttle control as shown on the 
picture. 

5. 

Mount the side guards using the bolts and nuts supplied. 
Note the side guard must go under the body frame.  

6. 

Mount the blades using the cotter bolts and pins. 

7. 

Mount the depth skid with the cotter bolt and pin. 

8. 

Fit the panel to the handlebar with the 4 screws. 
(only Lilli 572/575) 

Fill the engine with oil.  

See changing the oil section for more details. 

Clothing 

 
When using the machine, wear close-fitting work clothes, 
hard-wearing work gloves, ear defenders and non-slip boots 
with steel toecaps.  
 

Operating the tiller 

Ensure the machine is placed on a level surface with the 
support wheels lowered prior to start. 

Remove all foreign objects from the work area before 
using the machine. Stones, glass, branches and similar 
items may damage the tiller. Also, check the bolts on the 
tiller are tightened.   

Start the motor as per the instructions below. Stand 
clear of the machine’s moving parts. 

Never attempt to move the machine in any way other 
than intended for normal use while the motor is running. 

 
The tiller is designed for use in vegetable gardens and 
flowerbeds. Ensure that you are familiar with these 
instructions before operating the machine, in particular the 
motor start and stop procedures.  
 
Fig 9: To use the black handle the control stick must first be 
activated. By tilting the control stick to the right or left side 
and then activate the black handle lever, the tiller will move 
forward or backwards.