RU
3.
Пропустите нить через
направляющую (1), вводя
нитку справа.
4.
Ведите нитку вниз и
пропустите между шайбами
натяжения регулятора (2)
5.
Ведите нитку вверх.
Введите нитку в отверстие
нитепритягивателя справа на
лево (3).
6.
Протяните нитку вниз к
игле через направляющую
нитки (4) и через направляющую на
уровне иглы (5).
7.
Введите нитку в игольное ушко
спереди назад (6) и заведите нитку
под лапку, оставив конец примерно
10 см.
ВНИМАНИЕ: Также следует заправлять
нитку в двойную иглу.
1.
Во время заправки левой
иглы действуйте аналогично,
как и в случае заправки
одной иглы (нить через
пункты, обозначенные на
рисунке от 1 до 5).
2.
Далее провести нить
с наружной стороны
нитенаправителя (5), как
показано на рис.
3.
Введите нитку в игольное
ушко сзади.
4.
После заправки левой иглы,
заправить правую иглу.
Заправьте нитку обычным
способом.
5.
Введите нитку в игольное ушко спереди назад.
7
KNOWING
YOUR
SEWING
MACHINE
Twin needle
How to thread the double needle:
1. Thread the left needle according to the
way of threading single needle from step
one to step five, then fix the thread into
the double needle spring as point 5 in the
right picture. Draw thread down and slip it
into needle bar thread guide 6. Finally
thread into the left needle eye from front
to back.
2. Thread the right needle according to the
way of threading single needle from step
one to step nine.
Note: Be sure to thread the left needle
thread firstly then thread the right
needle thread. Put the thread spool
on the spool pin, make sure that the
left thread will run anti-clockwise,
the right thread will run clockwise.
Threading
the
machine
Raise take-up lever to its highest position
by turning hand wheel toward you. Raise
presser foot.
Place spool on spool pin as shown, with
thread coming from the back of the spool.
1. Draw thread into thread guide using both
hands.
2. Draw thread down into the tension area and
around the check spring holder.
3. Firmly draw thread up and through take-up
lever from right to left.
4. Then draw thread down and slip it into the
lower thread guide.
5. Do not block the thread into double needle
spring.
6. Draw thread down and slip it into needle bar
thread guide.
7. Thread needle eye from front to back.
Note: Cut the thread end with sharp
scissors for easier needle threading.
1
2
3
5
6
4
7
5
6
2
1
3
4
7
5
6
2
1
3
4
7
8
6
5
Right needle
thread
Left needle
thread
7
KNOWING
YOUR
SEWING
MACHINE
Twin needle
How to thread the double needle:
1. Thread the left needle according to the
way of threading single needle from step
one to step five, then fix the thread into
the double needle spring as point 5 in the
right picture. Draw thread down and slip it
into needle bar thread guide 6. Finally
thread into the left needle eye from front
to back.
2. Thread the right needle according to the
way of threading single needle from step
one to step nine.
Note: Be sure to thread the left needle
thread firstly then thread the right
needle thread. Put the thread spool
on the spool pin, make sure that the
left thread will run anti-clockwise,
the right thread will run clockwise.
Threading
the
machine
Raise take-up lever to its highest position
by turning hand wheel toward you. Raise
presser foot.
Place spool on spool pin as shown, with
thread coming from the back of the spool.
1. Draw thread into thread guide using both
hands.
2. Draw thread down into the tension area and
around the check spring holder.
3. Firmly draw thread up and through take-up
lever from right to left.
4. Then draw thread down and slip it into the
lower thread guide.
5. Do not block the thread into double needle
spring.
6. Draw thread down and slip it into needle bar
thread guide.
7. Thread needle eye from front to back.
Note: Cut the thread end with sharp
scissors for easier needle threading.
1
2
3
5
6
4
7
5
6
2
1
3
4
7
5
6
2
1
3
4
7
8
6
5
Right needle
thread
Left needle
thread
ДВОЙНАЯ ИГЛА
7
KNOWING
YOUR
SEWING
MACHINE
Twin needle
How to thread the double needle:
1. Thread the left needle according to the
way of threading single needle from step
one to step five, then fix the thread into
the double needle spring as point 5 in the
right picture. Draw thread down and slip it
into needle bar thread guide 6. Finally
thread into the left needle eye from front
to back.
2. Thread the right needle according to the
way of threading single needle from step
one to step nine.
Note: Be sure to thread the left needle
thread firstly then thread the right
needle thread. Put the thread spool
on the spool pin, make sure that the
left thread will run anti-clockwise,
the right thread will run clockwise.
Threading
the
machine
Raise take-up lever to its highest position
by turning hand wheel toward you. Raise
presser foot.
Place spool on spool pin as shown, with
thread coming from the back of the spool.
1. Draw thread into thread guide using both
hands.
2. Draw thread down into the tension area and
around the check spring holder.
3. Firmly draw thread up and through take-up
lever from right to left.
4. Then draw thread down and slip it into the
lower thread guide.
5. Do not block the thread into double needle
spring.
6. Draw thread down and slip it into needle bar
thread guide.
7. Thread needle eye from front to back.
Note: Cut the thread end with sharp
scissors for easier needle threading.
1
2
3
5
6
4
7
5
6
2
1
3
4
7
5
6
2
1
3
4
7
8
6
5
Right needle
thread
Left needle
thread
Нитка левой
иглы
Нитка правой
иглы
Texi Fox 25
182
Summary of Contents for Fox 25
