RU
ПРИШИВАНИЕ МОЛНИИ – ПРЯМАЯ СТРОЧКА
ПРИШИВАНИЕ ПУГОВИЦ
ЛАПКА – ДЛЯ ПРИШИВАНИЯ МОЛНИИ
1.
Установите лапку для пришивания
молнии.
2.
Расположите молнию на материале и
положите под лапку.
3.
При шитье левой стороны молнии лапка
должна находиться с правой стороны от
иглы.
4.
Расположите лапку так, чтобы шов был
как можно ближе к зубчикам молнии.
5.
Установите лапку с левой стороны,
чтобы пришить правую сторону молнии.
Расположите лапку так, чтобы шов был как можно ближе к зубчикам молнии.
6.
Поднимите лапку и расстегните молнию прежде чем лапка дойдет до конца.
ЛАПКА – ДЛЯ ПРИШИВАНИЯ ПУГОВИЦ
1.
Установите лапку для пришивания пуговиц.
2.
Отключите двигатель материала (транспортер),
перемещая рычаг транспортера на право, как
показано на рисунке.
3.
Установите на игольной пластине
дополнительную пластину для вышивки
(находится в столике с аксессуарами), установите
лапку универсальную либо лапку для пришивания пуговиц.
4.
Расположите материал и пуговицу под лапкой. Совместите оба отверстия пуговицы с
пазом прижимной лапки, а левое отверстие пуговицы поместите как раз под иглой.
5.
Установите ширину строчки , а затем опустите лапку и проверьте, соответствует ли
выбранная ширина отверстиям в пуговице: медленно поворачивая маховик до
момента когда игла окажется непосредственно над правым отверстием пуговицы. Если
необходимо, отрегулируйте ширину зигзага.
6.
Прострочите примерно 6-7 стежков (10 на плотном материале) и поднимите иглу.
7.
Чтобы упрочнить „ножку” оставьте конец нитки около 20 см. Протяните нижнюю нитку
через отверстие пуговицы и оберните ей несколько раз „ножку”.
8.
Протяните верхнюю нитку на изнаночную сторону и свяжите обе нитки.
В зависимости от того, какая сторона
молнии шьется (правая или левая)
лапка должна быть рядом с зубчиками
молнии.
18
UTILITY STITCHES
Helpful hint:
During zipper inserting, ensure that the
needle do not touch the zipper. Otherwise
it will cause needle break or even injury.
Buttonhole stitch
Zipper
application
Tips:
Slightly reduce the upper tension to
produce better results.
Use backing material for fine or
stretchy materials.
We recommend placing a pin across
the end of the buttonhole as a
precaution against cutting the stitches
with the seam ripper.
It is advisable to use gimp cord for
stretch or knit fabrics. The zigzag
should sew over the gimp.
The lines on the buttonhole foot can be
used guides when sewing multiple
buttonholes.
1. Lift the presser foot, pull the gimp cord and come round the protruding point on back of the
buttonhole foot.
2. Pull the gimp cord under the foot to the front.
3. Fix the gimp cord to the protruding point on front of foot.
4. Turn the needle down to the starting position on fabric, put down the presser foot.
5. Sew the buttonhole according to page 17.
6. Pull the gimp cord straightly.
7. Cut the gimp cord.
Attach the zipper foot.
When sewing the right side of the zipper, attach the
zipper foot as the illustration in right.
When sewing the left side of the zipper, attach the
zipper foot as the illustration in right.
Sew the right side
of the zipper.
Sew the left side
of the zipper.
A
3~6
2
Machine
Setting
18
UTILITY STITCHES
Helpful hint:
During zipper inserting, ensure that the
needle do not touch the zipper. Otherwise
it will cause needle break or even injury.
Buttonhole stitch
Zipper
application
Tips:
Slightly reduce the upper tension to
produce better results.
Use backing material for fine or
stretchy materials.
We recommend placing a pin across
the end of the buttonhole as a
precaution against cutting the stitches
with the seam ripper.
It is advisable to use gimp cord for
stretch or knit fabrics. The zigzag
should sew over the gimp.
The lines on the buttonhole foot can be
used guides when sewing multiple
buttonholes.
1. Lift the presser foot, pull the gimp cord and come round the protruding point on back of the
buttonhole foot.
2. Pull the gimp cord under the foot to the front.
3. Fix the gimp cord to the protruding point on front of foot.
4. Turn the needle down to the starting position on fabric, put down the presser foot.
5. Sew the buttonhole according to page 17.
6. Pull the gimp cord straightly.
7. Cut the gimp cord.
Attach the zipper foot.
When sewing the right side of the zipper, attach the
zipper foot as the illustration in right.
When sewing the left side of the zipper, attach the
zipper foot as the illustration in right.
Sew the right side
of the zipper.
Sew the left side
of the zipper.
A
3~6
2
Machine
Setting
16
UTILITY STITCHES
Sewing
buttons
To secure thread, cut the upper thread with 25cm of excess, wind it
around the thread between the button and the fabric, and then tie it
tightly.
Position your fabric and button under the presser foot. Lower presser foot. Turn the
handwheel to make sure needle clears both left and right openings of button. Adjust
width if required. Sew 10 stitches across.
When attaching four-hole buttons, first sew the two holes closest to you. Then, slide the
button so that the needle goes into the two holes toward the rear of the sewing machine,
and then sew them in the same way.
1
2
3
C~B
Machine Setting
1~3
NOTE: 1. Drop the feed dog (Refer to page 4) .
After you finish sewing, set the drop feed
lever to the original position.
2. You do not have to adjust the stitch length dial.
Drop
the
feed
dog
18
UTILITY STITCHES
Helpful hint:
During zipper inserting, ensure that the
needle do not touch the zipper. Otherwise
it will cause needle break or even injury.
Buttonhole stitch
Zipper
application
Tips:
Slightly reduce the upper tension to
produce better results.
Use backing material for fine or
stretchy materials.
We recommend placing a pin across
the end of the buttonhole as a
precaution against cutting the stitches
with the seam ripper.
It is advisable to use gimp cord for
stretch or knit fabrics. The zigzag
should sew over the gimp.
The lines on the buttonhole foot can be
used guides when sewing multiple
buttonholes.
1. Lift the presser foot, pull the gimp cord and come round the protruding point on back of the
buttonhole foot.
2. Pull the gimp cord under the foot to the front.
3. Fix the gimp cord to the protruding point on front of foot.
4. Turn the needle down to the starting position on fabric, put down the presser foot.
5. Sew the buttonhole according to page 17.
6. Pull the gimp cord straightly.
7. Cut the gimp cord.
Attach the zipper foot.
When sewing the right side of the zipper, attach the
zipper foot as the illustration in right.
When sewing the left side of the zipper, attach the
zipper foot as the illustration in right.
Sew the right side
of the zipper.
Sew the left side
of the zipper.
A
3~6
2
Machine
Setting
16
UTILITY STITCHES
Sewing
buttons
To secure thread, cut the upper thread with 25cm of excess, wind it
around the thread between the button and the fabric, and then tie it
tightly.
Position your fabric and button under the presser foot. Lower presser foot. Turn the
handwheel to make sure needle clears both left and right openings of button. Adjust
width if required. Sew 10 stitches across.
When attaching four-hole buttons, first sew the two holes closest to you. Then, slide the
button so that the needle goes into the two holes toward the rear of the sewing machine,
and then sew them in the same way.
1
2
3
C~B
Machine Setting
1~3
NOTE: 1. Drop the feed dog (Refer to page 4) .
After you finish sewing, set the drop feed
lever to the original position.
2. You do not have to adjust the stitch length dial.
Drop
the
feed
dog
16
UTILITY STITCHES
Sewing
buttons
To secure thread, cut the upper thread with 25cm of excess, wind it
around the thread between the button and the fabric, and then tie it
tightly.
Position your fabric and button under the presser foot. Lower presser foot. Turn the
handwheel to make sure needle clears both left and right openings of button. Adjust
width if required. Sew 10 stitches across.
When attaching four-hole buttons, first sew the two holes closest to you. Then, slide the
button so that the needle goes into the two holes toward the rear of the sewing machine,
and then sew them in the same way.
1
2
3
C~B
Machine Setting
1~3
NOTE: 1. Drop the feed dog (Refer to page 4) .
After you finish sewing, set the drop feed
lever to the original position.
2. You do not have to adjust the stitch length dial.
Drop
the
feed
dog
16
UTILITY STITCHES
Sewing
buttons
To secure thread, cut the upper thread with 25cm of excess, wind it
around the thread between the button and the fabric, and then tie it
tightly.
Position your fabric and button under the presser foot. Lower presser foot. Turn the
handwheel to make sure needle clears both left and right openings of button. Adjust
width if required. Sew 10 stitches across.
When attaching four-hole buttons, first sew the two holes closest to you. Then, slide the
button so that the needle goes into the two holes toward the rear of the sewing machine,
and then sew them in the same way.
1
2
3
C~B
Machine Setting
1~3
NOTE: 1. Drop the feed dog (Refer to page 4) .
After you finish sewing, set the drop feed
lever to the original position.
2. You do not have to adjust the stitch length dial.
Drop
the
feed
dog
16
UTILITY STITCHES
Sewing
buttons
To secure thread, cut the upper thread with 25cm of excess, wind it
around the thread between the button and the fabric, and then tie it
tightly.
Position your fabric and button under the presser foot. Lower presser foot. Turn the
handwheel to make sure needle clears both left and right openings of button. Adjust
width if required. Sew 10 stitches across.
When attaching four-hole buttons, first sew the two holes closest to you. Then, slide the
button so that the needle goes into the two holes toward the rear of the sewing machine,
and then sew them in the same way.
1
2
3
C~B
Machine Setting
1~3
NOTE: 1. Drop the feed dog (Refer to page 4) .
After you finish sewing, set the drop feed
lever to the original position.
2. You do not have to adjust the stitch length dial.
Drop
the
feed
dog
Texi Fox 25
191
Summary of Contents for Fox 25
