Texi Fox 25 User Manual Download

Page: 68 / 200

THREAD STAND

WINDING THE BOBBIN

REMOVING OR INSERTING THE BOBBIN CASE

The spool pins are used for holding the spool of

thread in order to feed thread to the machine.

To use, pull up the spool pin. Push down for

storage.

Place a spool of thread onto the spool pin. Guide

the thread around the bobbin winder thread

guide.

Insert the thread through one of holes in the

bobbin from the inside to the outside.

Put the bobbin on the bobbin winder spindle,

and push it to the right. With the free end of

the thread held in your hand, depress the foot

control.

Stop the machine when it has made a few

turns, and cut the thread close to the hole in the

bobbin. Depress the foot control again. When the

bobbin is fully wound, it will stop automatically.

Return the bobbin winder to its original position

by moving the spindle to the left, and cut the thread.

CAUTION: Turn off the power before start this operation.

Raise the needle by turning the hand wheel toward you.

Open the hook cover.

Take out bobbin case holding the latch.

When inserting the bobbin case, place the tip of the bobbin case into the recess of

the hookrace.

Linie na płytce

ciegowej pomagaj

zachowa

wła

ciw

odległo

ść

ciegu od kraw

dzi materia-

łu (a konkretnie od centralnego uderzenia igły).

Warto

ci liczbowe pokazane s

zarówno w ca-

lach (z tyłu płytki), jak i w milimetrach (z przodu
płytki).

OZNACZENIA NA PŁYTCE

CIEGOWEJ

W zapakowanej fabrycznie maszynie stojaki na nici s

wci

te (schowane w obudowie), aby nie uległy

uszkodzeniu. Przed rozpocz

ciem szycia nale

y je

wyci

ąć

do góry, natomiast zawsze przed zapako-

waniem maszyny do kartonu, walizki czy cho

by po-

krowca, nale

y wciska

stojaki w dół w obudow

STOJAKI NA NICI

NAWIJANIE NICI NA SZPULK

1. Nałó

szpul

z nici

na jeden ze stojaków Poci

gnij nitk

ze szpulki i przeprowad

przez prowadnik na pokrywie gór-

nej (1)

2. Przeci

gnij nitk

przez otwór w szpulce od wewn

trz na

zewn

trz i załó

szpulk

benka na trzpie

szpulownika.

3. Przesu

trzpie

ze szpulk

w prawo (2).

5. Przytrzymaj za koniec nitki i naci

nij rozrusznik rozpo-

czynaj

c nawijanie. Zatrzymaj maszyn

po nawini

ciu kilku

zwojów i utnij nitk

blisko otworu w szpulce (3).

KNOWING

YOUR

SEWING

MACHINE

KNOWING

YOUR

SEWING

MACHINE

Seam guide line

The numbers on the needle plate indicate
the distance between the center needle
position and the indicating line.
The numbers in the front indicate in
Millimeters.
The numbers in the back indicate in inches.

Setting spool pins

The spool pins are used for holding the spool of thread in order
to feed thread to the machine.
To use, pull up the spool pin. Push down for storage.

Winding the bobbin

1. Place a spool of thread on the left spool pin. Pull

the thread out from the spool and place it through
thread guide as shown in illustration. Put end of
thread through the hole in bobbin as shown.

2. Push the bobbin wider shaft to far left position, if

it is not already there. Place bobbin onto the
bobbin wider shaft with end of thread coming
from top of bobbin. Push bobbin winder shaft to
the right until it clicks. Hold onto end of thread.

3. Start machine. Bobbin will automatically stop

turning when completely filled. Push shaft to the
left to remove bobbin and cut thread.

KNOWING

YOUR

SEWING

MACHINE

Removing or replace the bobbin case

1. Refer to page 4 to remove the Extension table, raise the needle by turning the hand wheel

toward you, then open the shuttle cover.

2. Take out bobbin case holding the latch.
3. When installing the bobbin case, the pin on the case should fit into the gap of the shuttle race.

Threading the bobbin case

1. Install the bobbin into bobbin case. Make sure the thread unwinds in the direction of arrow.
2. Pull the thread into the groove in the bobbin case slot.
3. Now pull the thread under the tension spring and into the delivery eye.

NOTE: Leave about 10cm (4 inches) of the thread hanging out of the bobbin case. When

you pull the thread, the bobbin should spin clockwise.

Changing the presser foot

1. Turn the hand wheel toward you to raise the needle to its highest position.

Raise the presser foot.

2. Press the lever on the back of the presser foot holder. The presser foot will drop off.
3. Place the presser foot so the pin on the foot lies just under the groove of the holder.

Lower the presser foot holder to lock the foot in place.

Be sure to disconnect the power supply before operating the machine.

Attaching the seam guide(optional)

Attach the seam guide in the slot as illustrated. adjust according to

need for hems pleats etc.

Gap

Texi Fox 25