CL-B101D40-TCRTD Manual (d0099)
Page 1
Smart 101 segment 4 digit LED Tricolor or Mono-color
digital bargraph controller with four fully programmable
set points for J, K, R, and T type thermocouples and
RTD inputs in a switchboard style case.
0.56” LEDs
• External transmitters or signal conditioners can be eliminated by
direct connection of the sensor output to Plug-in Input Signal
Conditioners- available are thermocouples (J, K, R and T types)
or RTD (Pt-100. 385 and 392 curves. 3 wire/4wire). Digitally
Linearized.
• Optional isolated 16 bit analog output. User or factory scalable to 4
to 20 mA, 0 to 20 mA or 0 to 10 V across any desired digital span
from ± one count to the full scale range of – 1999 to 9999 (12000
counts).
• A Programmable Tricolor (Red-Green-Orange) or mono color (red or
green), 101 segment high brightness bargraph.
• Red 4-digit LED display with a range of -1999 to 9999
(12000 counts). Optional green digital display.
• Front panel LED annunciators provide indication of setpoint status.
• Two 9 Amp Form C, and two 4 Amp Form A or 4 x 4 Amp Form A
relays available.
• Auto-sensing AC/DC power supply. For voltages between
85-265 V AC / 95-300 V DC (PS1) or 18-48 V AC / 10-72 V DC
(PS2).
• Provision to connect an external programming lockout switch.
• Provision for external DIM switch to reduce the brightest
display setting by 50%.
• Automatic intelligent averaging, smooths noisy signals while
providing a fast display response to real level changes.
General Features
Specifications
• The bargraph can display, full
scale, any desired portion of
the digital reading.
• Setpoint 1 has delay-on-make
and delay-on-break plus
a special “pump on pump
off” mode that creates a
Hysteresis Band between SP1
and SP2.
Software Features
• Four programmable setpoints
with adjustable Hysteresis.•
Bargraph center zero function.
• Relay activation can be select-
ed to occur above (hi) or below
(Lo) each setpoint.
• Digital display blanking.
• Decimal point setting.
• Four-level brightness control
LEOPARD
FAMILY
Input Specs
: ������������������Depends on Input signal conditioner
A/D Converter
: ��������������14 bit single slope
Accuracy
: ����������������������±(0�05% of r 2 counts)
Temp. Coeff
�: �����������������100 ppm/°C (Typical)
Warm up time
: ���������������2 minutes
Conversion Rate
: ����������10 conversions per second (Typical)
Digital Display
: ��������������
4 digit 0.56" LED red (std)
, green (optn)
Range –1999 to 9999 counts�
Bargraph Display
: ���������
101 segment 235º circular red (standard)
,
Green (optional) or tricolor (optional) LED�
Polarity
: �������������������������Assumed positive� Displays – negative
Decimal Selection
: ��������
Front panel button selectable, X•X•X•X•
Positive Overrange
: ������Bargraph and top segments of digital display
flash�
Negative Overrange
: ����First segment of bargraph and bottom seg-
ments of digital display flash�
Relay Output
: ����������������Two 9 Amp Form C relays, two 4 Amp Form
A relays or
4 x 4 Amp Form A relays
Analog Output
: �������������Isolated 16 bit user scalable mA or V
OIC (mA out) ��������������
4-20 mA @ 0 to 500Ω max loop resistance
OIV (volts out) ��������������
0-10 V DC @ 500 Ω or higher resistance
Power Supply
: ���������������AC/DC Auto sensing wide range supply
PS1 (std)
��������������������
85-265 VAC / 95-300 VDC, 50-400Hz 4.2W
PS2 �����������������������������18-48 VAC / 10-72 VDC, 50-400Hz 4�2W
Operating Temp
�: ����������0 to 60°C
Storage Temp
: ���������������–20°C to 70°C
Relative Humidity
: ��������95% (non condensing)
Case Dimensions
: ��������
Bezel (4.48"x4.48") 113.8x113.8mm
Depth behind bezel (4.23") 107.46 mm
Plus (0�48”) 12�24 mm for connectors
Weight
: ���������������������������16 oz�, 1lb 4 oz when packed
Table of Contents
Bargraph Center Point Display Mode Selection . . . 6
Bargraph Color Programming Mode . . . . . . . . 9
Case Dimensions . . . . . . . . . . . . . . . . . . . . . . 11
Component Layout. . . . . . . . . . . . . . . . . . . . . 11
Connector Pinouts . . . . . . . . . . . . . . . . . . .10-11
Controls and Indicators . . . . . . . . . . . . . . . . . . 2
Decimal Point and Brightness Selection . . . . . 5
Programming Conventions. . . . . . . . . . . . . . . . 2
Setpoint Setting & Relay Conf. Mode . . . . . .8-9
Software Features . . . . . . . . . . . . . . . . . . . . . . 1
Software Logic Tree . . . . . . . . . . . . . . . . . . . . . 3
Specifications. . . . . . . . . . . . . . . . . . . . . . . . . . 1
Two Point Analog Range Setting & Calibration . . . . 7
Thermocouple and RTD Type Selection Mode. . . . . .4
Digital Span Selection for Bargraph Display . . 5
Digital Span Selection for Analog Range Output. . . 6
Functional Diagram . . . . . . . . . . . . . . . . . . . . 10
General Features . . . . . . . . . . . . . . . . . . . . . . . 1
Input Module Calibration Procedures . . . . . . 12
Ordering Information . . . . . . . . . . . . . . . . . . . 13
Pin Descriptions . . . . . . . . . . . . . . . . . . . . . . . 10
